The CDi 4|600BL is a four-channel installation amplifier from the Crown CDi DriveCore series, rated at 600W per channel into 4 ohms. Each channel drives low-impedance speakers or a 70V or 100V distributed speaker line directly, with no output transformer. It suits medium-sized installations such as cinemas, houses of worship, bars and lounges.

Besides its analog inputs, it has BLU link, so it can send and receive audio channels on a BLU link digital audio bus. The onboard DSP comes loaded with JBL speaker tunings. Set the amplifier up from the front panel, or configure and monitor it over a standard network with HiQnet Audio Architect software.

Features

  • DriveCore technology, which removes hundreds of components from each amplifier
  • Direct drive 70V or 100V output on every channel, with no step-up transformer
  • BLU link: sends and receives channels on the 256-channel, fault-tolerant BLU link digital audio bus
  • Bridge mono mode on channel pairs for higher-power loads
  • Onboard DSP: input router, input delay up to 1000 ms, 8-band input parametric EQ, crossover, 8-band output parametric EQ, output delay up to 100 ms and LevelMAX limiter
  • Preloaded JBL speaker tunings
  • Front-panel interface for complete setup at the amplifier
  • Network control and monitoring over standard TCP/IP with HiQnet Audio Architect software
  • Combined GPIO/aux port to recall presets, mute channels, monitor faults and switch the amplifier on or off

Specifications

  • Channels: 4
  • Inputs: Analog and BLU link
  • Output power per channel, all channels driven: 300W at 2 ohms, 600W at 4 ohms, 600W at 8 ohms, 300W at 16 ohms, 600W at 70V, 600W at 100V
  • Bridge mono output power: 600W at 4 ohms, 1200W at 8 ohms, 1200W at 16 ohms, 1200W at 140V, 1200W at 200V
  • Power rating: Minimum guaranteed power at 1 kHz, all channels driven, 0.5% maximum distortion, 0.5 second duration
  • Input sensitivity: 0.7V RMS for full rated power at 8 ohms
  • Signal-to-noise ratio: More than 104 dB (analog input, ref. rated power, 20 Hz to 20 kHz)
  • THD: 0.35% at full rated power, 20 Hz to 20 kHz
  • Frequency response: ±0.25 dB, 20 Hz to 20 kHz (8 ohms)
  • Damping factor: More than 1000 (20 Hz to 100 Hz)
  • Crosstalk: More than 80 dB (20 Hz to 1 kHz)
  • Input impedance: 10k ohms balanced, 5k ohms unbalanced
  • AC power: 15A IEC, 100 to 240V AC
  • Dimensions (W x H x D): 19 x 3.5 x 12.25 in. (48.3 x 8.9 x 31.1 cm), depth without the 1.3 in. (3.3 cm) front panel
  • Weight: 16.3 lb (7.39 kg)

In the Box

  • CDi 4|600BL amplifier
  • AC power cord
  • Plug-in input connectors
  • Terminal fork connectors for the speaker outputs
  • Important Safety Instructions

Annonces similaires mises en avant













ÉtatNeuf (neuf)
Le matériel en état « Neuf » n'est vendu que par un vendeur autorisé ou un fabricant et inclut l'emballage d'origine.En savoir plus
Marque
Modèle
  • Crown CDi 4|600BL DriveCore Installation Power Amplifier with BLU link
Catégories

Des informations concernant la sécurité des produits peuvent être disponibles ici.

À propos du vendeur

Blackout Audio

Toronto, Canada
Membre de Reverb depuis:2023

Protection Reverb

Retours simples, transactions sécurisées, service client humain

En savoir plus

Paiement sécurisé

Reverb Gives

Vos achats aident les programmes de musique destinés aux jeunes à obtenir le matériel dont ils ont besoin pour faire de la musique.

Oups, il semblerait que vous avez oublié quelque chose. Veuillez corriger les champs affichés en rouge.