The CDi 4|300BL is a four-channel installation amplifier from the Crown CDi DriveCore series, rated at 300W per channel into 4 ohms. Each channel drives low-impedance speakers or a 70V or 100V distributed speaker line directly, with no output transformer. It suits small and medium installations such as restaurants and retail stores.

Besides its analog inputs, it has BLU link, so it can send and receive audio channels on a BLU link digital audio bus. The onboard DSP comes loaded with JBL speaker tunings. Set the amplifier up from the front panel, or configure and monitor it over a standard network with HiQnet Audio Architect software.

Features

  • DriveCore technology, which removes hundreds of components from each amplifier
  • Direct drive 70V or 100V output on every channel, with no step-up transformer
  • BLU link: sends and receives channels on the 256-channel, fault-tolerant BLU link digital audio bus
  • Bridge mono mode on channel pairs for higher-power loads
  • Onboard DSP: input router, input delay up to 1000 ms, 8-band input parametric EQ, crossover, 8-band output parametric EQ, output delay up to 100 ms and LevelMAX limiter
  • Preloaded JBL speaker tunings
  • Front-panel interface for complete setup at the amplifier
  • Network control and monitoring over standard TCP/IP with HiQnet Audio Architect software
  • Combined GPIO/aux port to recall presets, mute channels, monitor faults and switch the amplifier on or off

Specifications

  • Channels: 4
  • Inputs: Analog and BLU link
  • Output power per channel, all channels driven: 150W at 2 ohms, 300W at 4 ohms, 300W at 8 ohms, 150W at 16 ohms, 300W at 70V, 300W at 100V
  • Bridge mono output power: 300W at 4 ohms, 600W at 8 ohms, 600W at 16 ohms, 600W at 140V, 600W at 200V
  • Power rating: Minimum guaranteed power at 1 kHz, all channels driven, 0.5% maximum distortion, 0.5 second duration
  • Input sensitivity: 0.7V RMS for full rated power at 8 ohms
  • Signal-to-noise ratio: More than 104 dB (analog input, ref. rated power, 20 Hz to 20 kHz)
  • THD: 0.35% at full rated power, 20 Hz to 20 kHz
  • Frequency response: ±0.5 dB, 20 Hz to 20 kHz (8 ohms)
  • Damping factor: More than 1000 (20 Hz to 100 Hz)
  • Crosstalk: More than 80 dB (20 Hz to 1 kHz)
  • Input impedance: 20k ohms balanced, 10k ohms unbalanced
  • AC power: IEC 320 inlet, 100 to 240V AC
  • Dimensions (W x H x D): 19 x 3.5 x 12.25 in. (48.3 x 8.9 x 31.1 cm), depth without the 1.3 in. (3.3 cm) front panel
  • Weight: 16.13 lb (7.31 kg)

In the Box

  • CDi 4|300BL amplifier
  • AC power cord
  • Plug-in input connectors
  • Terminal fork connectors for the speaker outputs
  • Important Safety Instructions

Annonces similaires mises en avant













ÉtatNeuf (neuf)
Le matériel en état « Neuf » n'est vendu que par un vendeur autorisé ou un fabricant et inclut l'emballage d'origine.En savoir plus
Marque
Modèle
  • Crown CDi 4|300BL DriveCore Installation Power Amplifier with BLU link
Catégories

Des informations concernant la sécurité des produits peuvent être disponibles ici.

À propos du vendeur

Blackout Audio

Toronto, Canada
Membre de Reverb depuis:2023

Protection Reverb

Retours simples, transactions sécurisées, service client humain

En savoir plus

Paiement sécurisé

Reverb Gives

Vos achats aident les programmes de musique destinés aux jeunes à obtenir le matériel dont ils ont besoin pour faire de la musique.

Oups, il semblerait que vous avez oublié quelque chose. Veuillez corriger les champs affichés en rouge.