Crown CDi 2|600BL DriveCore Installation Power Amplifier with BLU link
The CDi 2|600BL is a two-channel installation amplifier from the Crown CDi DriveCore series, rated at 600W per channel into 4 ohms. Each channel drives low-impedance speakers or a 70V or 100V distributed speaker line directly, with no output transformer. It suits medium-sized installations such as cinemas, houses of worship, bars and lounges.
Besides its analog inputs, it has BLU link, so it can send and receive audio channels on a BLU link digital audio bus. The onboard DSP comes loaded with JBL speaker tunings. Set the amplifier up from the front panel, or configure and monitor it over a standard network with HiQnet Audio Architect software.
Features
- DriveCore technology, which removes hundreds of components from each amplifier
- Direct drive 70V or 100V output on every channel, with no step-up transformer
- BLU link: sends and receives channels on the 256-channel, fault-tolerant BLU link digital audio bus
- Bridge mono mode on channel pairs for higher-power loads
- Onboard DSP: input router, input delay up to 1000 ms, 8-band input parametric EQ, crossover, 8-band output parametric EQ, output delay up to 100 ms and LevelMAX limiter
- Preloaded JBL speaker tunings
- Front-panel interface for complete setup at the amplifier
- Network control and monitoring over standard TCP/IP with HiQnet Audio Architect software
- Combined GPIO/aux port to recall presets, mute channels, monitor faults and switch the amplifier on or off
Specifications
- Channels: 2
- Inputs: Analog and BLU link
- Output power per channel, all channels driven: 300W at 2 ohms, 600W at 4 ohms, 600W at 8 ohms, 300W at 16 ohms, 600W at 70V, 600W at 100V
- Bridge mono output power: 600W at 4 ohms, 1200W at 8 ohms, 1200W at 16 ohms, 1200W at 140V, 1200W at 200V
- Power rating: Minimum guaranteed power at 1 kHz, all channels driven, 0.5% maximum distortion, 0.5 second duration
- Input sensitivity: 0.7V RMS for full rated power at 8 ohms
- Signal-to-noise ratio: More than 104 dB (analog input, ref. rated power, 20 Hz to 20 kHz)
- THD: 0.35% at full rated power, 20 Hz to 20 kHz
- Frequency response: ±0.5 dB, 20 Hz to 20 kHz (8 ohms)
- Damping factor: More than 1000 (20 Hz to 100 Hz)
- Crosstalk: More than 80 dB (20 Hz to 1 kHz)
- Input impedance: 20k ohms balanced, 10k ohms unbalanced
- AC power: IEC 320 inlet, 100 to 240V AC
- Dimensions (W x H x D): 19 x 3.5 x 12.25 in. (48.3 x 8.9 x 31.1 cm), depth without the 1.3 in. (3.3 cm) front panel
- Weight: 14.56 lb (6.6 kg)
In the Box
- CDi 2|600BL amplifier
- AC power cord
- Plug-in input connectors
- Terminal fork connectors for the speaker outputs
- Important Safety Instructions
| État | Neuf (neuf) Le matériel en état « Neuf » n'est vendu que par un vendeur autorisé ou un fabricant et inclut l'emballage d'origine.En savoir plus |
|---|---|
| Marque | |
| Modèle |
|
| Catégories |
Des informations concernant la sécurité des produits peuvent être disponibles ici.

