JENSEN P12 HEMP FIBER CONE 16 OHMS 2 AVAILABLE 30 WATTS OF FAT THICK MEATY TONALITY P.M.R. SPEAKER 1950s

******SEE MY OTHER LISTINGS!!!AND COMPLETE DESCRIPTION BELOW*****

*****TWO AVAILABLE / EACH PURCHASE IS FOR A SINGLE UNIT******

*NOTE- I posted these as B-Stock, so as to offer more than 1 unit, and that Reverb doesn't have a condition description for "completely re-fabricated/ like new"*

Up for grabs is this TREMENDOUS sounding Jensen 12" AlNiCo+ brass sleeve + hemp fiber cone speakers./..

AlNiCo+ brass+ hemp= fat, thick, meaty tonality... AAAND_ when you use the special 11 gram, neck dipped proprietary HEMPOPOTAMUS curve-linear G3 cone assembly, you also get speed, resolution, accuracy, and a well balanced midrange and top end that is even BETTER than the usual HEMP-O!

These units were completely re-fabricated at PMR in Ohio with all new OEM/ AMERICAN made components.

There are no after market, replacement, or import Chyna crap in it , but ONLY AMERICAN made parts....

.......'Fellas', even if you don't buy from me- BUY AMERICAN!

These 1950s gems were stripped down to bare metal and magnet, and then EVERYTHING was replaced. From the inside out, it's basically a new speaker again- ONLY BETTER!

The magnetic gap was verified with a gauss/flux probe and measured just fine, so it was PURPOSELY NOT de-magnetized/ re-magnetized...Some people say these old OEM magnetic assemblies "sweeten with age", and after I heard it, I HAVE to agree!!!

The frames were stripped down, and then shot with a nice silver ....

Then- EVERYTHING from the inside out is all new components....

I'll itemize:

*Front gaskets- I found a set of RuBiTex gaskets with the 4/8 hole mounting pattern, so I used these for cosmetic and air tight ability/appearances...

*Litz wires-- these are COPPER lit wires... After measuring the industry standard silver/gray "pot-metal" woven conductors, I now use COPPER on ALL of my rebuilds, new units , and customer's repairs. That gray stuff does nothing but smudge and smear the signal BEFORE it even gets to your voice coil.. By using copper- you get TRUE signal transference to the coils, and your tonality will show it.

* Spider assembly- I can't say there's anything too far out of the ordinary here.I used a high compliance treated textile.....And- she has a cupped profile should you need that much excursion...

*Voice coil... Now, this is a pretty nice coil... I REFUSE to use any of that CCAW or steel, or aluminum crap. I ONLY use solid copper wound coils..... Plus, this one is wound onto that special KAPTON and Kraft paper ,,,,, which really preserves and transfers tonality right into the cone assembly...It's a 16 Ohm coil, and handles 30 watts..

*Dust Cap- It's an ALUMINUM, but without any "Ice-Pick", or "beaming" like tonality,it really extends response out past 6KHz!... The way I accomplished that was that I wiped the inside surface of the cap LIGHTLY with ReZon-Ex to dampen out that harshness , yet allow the frequency extension...

*Surround- This is also a hemp fiber material, as it's part of the molded hemp fiber cone assembly...It was treated with special Eastman Kodak chemicals to loosen the fibers in THAT AREA ONLY, and aids in low frequency response. 

*CONE- This is the G3 HEMPO pulp recipe', and is around 11-12 grams/ non pressed, and has that beautifully deep curve-linear profile to it..

This unit really is greater than the sum of its parts.... I can't really add anything constructive to the descriptions I've already typed..

***. Fully tested under diagnostics and operates without any rubbing, smoking, buzzing, holes, rips, or tears- it's basically a brand new speaker- ONLY BETTER!

Plus, I'm confident enough that you guys will LOVE this one, that I am including my 15 day " NO GAMBLE" return option from delivery date (((less customer damage))) if for ANY reason you simply don't like it, or you dis-agree with ANYTHING I just typed...

So, if you want an AlNiCo 12" Jensen P12 high performance hemp fiber speaker ( or two) that's fat, thick, meaty and a 3D presentation....., then here ya' go!

ANY questions or concerns, just ask.

THANKS GUYS!!!