Sansui AU-D607 1979 Integrated Amp MM/MC, 2 phono Inputs 70 wpc, Black

Sansui AU-D607, just serviced. Japanese Domestic Item, 100v. Comes with stepdown transformer. Imported from Japan, serviced at Hyle’s Audio in Johnson City, NY w/ receipts.

This is a DC pre-main amplifier equipped with a diamond differential circuit that identifies the essence of audio amplifier as music playback.

The design further improves the DC conversion of the amplifier section. The equalizer section, flat amplifier section, and power amplifier section are all composed of DC amplifiers with excellent dynamic characteristics.

In addition, all block stage inputs are all FET inputs and are used as a push-pull input circuit, and the input capacitors of all block stages are eliminated in the direct coupling system.

This eliminates the low-frequency phase rotation that occurs when a capacitor enters the signal path, and other factors that degrade sound quality. As a result, pure music signal transmission and a wide range are achieved.

A diamond differential circuit is mounted on the power amplifier.

The first stage adopts a differential circuit with constant current using dual FET capable of passing a large current with low noise characteristics, and the second stage adopts a diamond differential circuit with cascode bootstrap.

And, NM (Non Magnetic) transistor with good linearity is used for the power stage, and the whole circuit is composed of symmetrical symmetrical circuit and 2 pole phase correction circuit, which realizes waveform transmission with little distortion up to high frequency range.

The circuit configuration of the equalizer amplifier section is a direct-coupled system in which input capacitors that cause sound quality degradation are removed. A high-stability, low-noise, high-gm dual FET is used for the first stage, a push-pull drive with two differential stages and a current differential with a current mirror is used, and a pure SEPP output is provided.

The equalizer for the NF circuit uses a high-precision metal film resistor and a styrofoam capacitor with low capacitance error and excellent temperature characteristics.

The flat amplifier section also uses a direct coupling method without input capacitors that are not effective in sound quality.

The first stage consists of cascode connection and differential amplification with current source using dual FET of low-noise and high-gm, and the second stage consists of 8 devices using current differential push-pull circuit with current mirror. Like the DC power amplifier section, it has excellent open-loop characteristics to reduce TIM distortion.

When the tone is turned on, the flat amplifier is switched to an NF-type tone amplifier, which provides a simple tone control characteristic with less distortion.

The power supply section is a 2-power transformer, and the left and right sides are completely independent.

In addition, by using 12,000 μ Fx4 electrolytic capacitors and metalized film capacitors, low impedance characteristics from ultra-low band to ultra-high band are achieved.

Equipped with MC head amplifier.

Equipped with a loudness switch, subsonic filter, Tone defeat switch and balance control.

Tape play function and tape copy function can be performed independently, and the tuner signal can be extracted independently for recording.

For example, you can air check while listening to a record.

The speaker output can be connected in two ways : OFF, A, B, or A + B.

Three spare AC outlets (100W for one interlocked circuit, 250W for two non-interlocked circuits) and ground terminal are mounted.

Pre-power and power can be separated.

Type Wide-range DC pre-main amplifier

Power Amplifier Unit

Effective power 70W + 70W (10 Hz ~ 20 kHz, THD 0.008%, 8 Ω)

70W + 70W (1 kHz, THD 0.003%, 8 Ω)

Total harmonic distortion factor 0.008% or Less (10 Hz to 20 kHz, 8 Ω at Effective Output)

Intermodulation distortion factor (70 hz : 7 khz = 4 : 1) Not more than 0.008%

Output bandwidth 5 Hz ~ 70 kHz (IHF, Both Channel Operation, 1 kHz, 8 Ω)

Damping factor 100 (IHF, Double-channel Operation, 1 kHz, 8 Ω)

Frequency characteristic DC ~ 400 kHz, + 0 -3dB

Input Sensitivity / Input Impedance 1V/47k Ω (1 kHz)

Signal-to-noise ratio 125 dB or more (IHF, A-network, short circuit)

Channel separation 90 dB or More (IHF, 1 kHz)

Rise time 0.5 μ sec

Slew rate ± 160 V / μ sec

Preamplifier Section

Input Sensitivity / Input Impedance

(1kHz) Phono-1MM : 2.5mV/47k Ω

Phono-2MC Only : 0.1mV/100 Ω

AUX, Tuner, Tape Play 1, 2 (PIN) : 150mV/47k Ω

MC compatible impedance 100 Ω or less

Phono maximum allowable input (1 kHz) Phono MM:300mV(THD 0.01%)

Phono MC:15mV(THD 0.03%)

Output Voltage (1 kHz) Tape Rec1, 2 (at PIN, 47k Ω) : 150 mv

Pre Out (at 47k Ω) : 1 V

Max Pre Out (at THD 0.05%, 47k Ω) : 4 v

Output Impedance (1 kHz) Tape Rec1, 2 : 600 Ω or less

Total harmonic distortion factor Phono MC (1 kHz, 6 V) : 0.01% or less

Phono MM (20 Hz to 20 kHz, 6 V) : 0.005% or less

AUX, Tuner, Tape Play 1, 2 (20 Hz to 20 kHz, 1 V) : 0.005% or less

Intermodulation distortion factor (70 hz : 7 khz = 4 : 1) AUX, Tuner, Tape Play 1, 2 (1 v) : not more than 0.005%

Frequency characteristic RIAA deviation (Phono 1, 2, 20 Hz-20 kHz) + / - 0.2 dB

AUX, Tuner, Tape Play 1, 2 : 5 hz to 100 khz, + 0 -1dB

Signal-to-noise ratio (IHF, A-network

Short circuit) Phono MC (input conversion) : -152dBV

Phono MM : 88 dB or more

AUX, Tuner, Tape Play 1, 2 : 100 dB or more

Channel separation

(IHF, 1 kHz) Phono MC : 70 dB or more

Phono MM : 70 dB or more

AUX, Tuner, Tape Play 1, 2 : 75 dB or higher

Input-to-input separation

(input short, 1 kHz) Tuner ⇔ Phono MM : 90 dB or higher

Tape Play 1, 2 ⇔ Phono MM : 90 dB or more

Tuner ⇔ Tape Play 1, 2 : 90 dB or higher

Tape Play 1 ⇔ Tape Play 2 : 90 dB or higher

Tone control Bass : ± 10 dB (50 Hz)

Treble : ± 10 dB (15 kHz)

Subsonic filter 16 Hz (-3dB, 6dB/oct.)

Loudness

(at volume -30dB) +10dB(50Hz)

+4dB(10kHz)

Headphone jack output 85 mw (8 Ω)

<General>

Load impedance 4 ~ 16 Ω

Rated power consumption 195W (Electrical Appliance and Material Control Law)

External dimensions Width 430x Height 168x Depth 390 mm

With Rack-Mount Adapter : Width 482x Depth 418 mm

Weight 15.5kg

With rack-mount adapter : 16 kg

Sold Separately Rack-Mount Adapter BX-7 (1 pair, ¥ 3,000)

I use reverb safe shipping or RSS for all purchases, it’s fairly cheap, unless you charge Crazy prices, especially for them to be there, to deal with, and quickly resolve any and all issue., usually in a matter of days. This service is less than $10 for items between $200-$400, to give an example. We are also sometimes offered shipping discounts with some services, if possible I like to use my discount to try to upgrade my buyers shipping. Anyone that charges $100 for shipping and says they lose money on shipping, it’s only because they’re insurance value is so high with Reverb services, if they didn’t charge $2000 for a $700 item then they’re shipping prices would be just fine. All you’re paying for is a higher insurance value, if my items are described to work then according to the description you get a working item or your money back. Thanks for your support, ALL my items GUARANTEED to work as described. I pack well and ship multiple times a week. Good service should not cost an extra thousand dollars an item.