Up for sale is an MDLR CASE 45W Eurorack powered busboard with the manufacturer's recommended power supply—a MEAN WELL GSM60A18. I removed this board from my rig and upgraded to an 85W unit with a larger supply as my system demanded more power. It was used for a period of time in my smoke free home studio, but it is in perfect working order and in excellent cosmetic condition. A small power panel—a DC barrel jack with on/off switch affixed to a small metal frame—and case mounting hardware for the busboard (screws and thick plastic washers that act as small standoffs) is included. Setup simply requires plugging the two barrel jack wires into the busboard terminals. This is an excellent, straightforward power solution to any DIY Eurorack case.
Picture is of the actual product you are purchasing, not a stock image.
Technical specifications as provided by the manufacturer are as follows:
Power 45W
Dimensions 420 x 140mm
Height 23mm
Weight 400g
Outputs:
+12V / 2A
-12V / 1.2A
+5V / 1.5A
Output stability ±1% for 0-100% load
Input 18V ( 16V – 20V )
Output Connectors 40 x 16 pin IDC for flat cable
Input connectors WAGO spring terminals + 5.5 / 2.1 DC inlet
Protections:
Input overvoltage
Input reverse polarity
Output overvoltage
Output short current – automatic recovery
Output over current – automatic recovery
All output protections are independent for each rail
Efficiency 92%
Other Input common mode LC filter with high efficiency of canceling noise and interference from input connector
Additional input filter on each regulator for minimal output noise and interferences
Shield for reducing RF interferences from regulators
Star distribution topology on PCB
Each “beam” from star topology has 4 headers with noise canceling capacitors.
In star topology center are another noise canceling capacitors
A big ground plane on both sides of PCB
Blue LEDs indicate present and drop of output voltage
For any more information, please visit the MDLR CASE website @ MDLRCASE.com.
Picture is of the actual product you are purchasing, not a stock image.
Technical specifications as provided by the manufacturer are as follows:
Power 45W
Dimensions 420 x 140mm
Height 23mm
Weight 400g
Outputs:
+12V / 2A
-12V / 1.2A
+5V / 1.5A
Output stability ±1% for 0-100% load
Input 18V ( 16V – 20V )
Output Connectors 40 x 16 pin IDC for flat cable
Input connectors WAGO spring terminals + 5.5 / 2.1 DC inlet
Protections:
Input overvoltage
Input reverse polarity
Output overvoltage
Output short current – automatic recovery
Output over current – automatic recovery
All output protections are independent for each rail
Efficiency 92%
Other Input common mode LC filter with high efficiency of canceling noise and interference from input connector
Additional input filter on each regulator for minimal output noise and interferences
Shield for reducing RF interferences from regulators
Star distribution topology on PCB
Each “beam” from star topology has 4 headers with noise canceling capacitors.
In star topology center are another noise canceling capacitors
A big ground plane on both sides of PCB
Blue LEDs indicate present and drop of output voltage
For any more information, please visit the MDLR CASE website @ MDLRCASE.com.
Protezione di Reverb per gli acquirenti
Reverb ti protegge nel caso in cui il tuo articolo venga perso, danneggiato o non corrisponda alla descrizione. Basta segnalare eventuali problemi entro 7 giorni e ti aiuteremo a ottenere il rimborso completo.Scopri di più sulla Protezione di Reverb per gli acquirenti.
| Pubblicato | 5 anni fa |
|---|---|
| Condizione | Eccellente (Usato) Gli articoli "Eccellenti" sono quasi completamente privi di difetti e altri difetti visivi e sono stati suonati o utilizzati con la massima cura.Scopri di più |
| Marchio | |
| Modello |
|
| Finish |
|
| Categorie | |
| Anno |
|
| Prodotto in |
|
Le informazioni sulla sicurezza del prodotto sono disponibili qui.



