JBL MPX1200

Greetings I have for sale a  working JBL MX1200 mpx 1200 power amplifier that I am asking 800 for.   This amp weight 65  lbs  so I will quote a high estimate on freight and then we will work out  particulars  and exact cost  to your area.  If you have a Fed Ex account we could ship on your account as well.  I am a good guy and easy to work with . The shipping is  based on a rough estimate of 1 power amps .  As mentioned will work with you  on freight  so do not freak on the estimated prices , please and thanks. These amps function as they should , t  You can see on the back no broken binding posts , overall good shape lived in racks since new. This amp ran the low end on my JBL SR Rig and was real warm.  I believe these amps were made by QSC for JBL but I may be wrong on that .

Will not ship outside of North America , repeat will not ship outside of North America , to costly .

Here is some info from JBL on the MPX1200

SPECIFICATIONS:

• 1600 Watts/CH into 2 Ohms
• 1200 Watts/CH into 4 Ohms
• 800 Watts/CH into 8 Ohms
• 3200 Watts Bridged-Mono into 4 Ohms

NOMINAL RATED OUTPUT POWER: (both channels driven 20 Hz - 20 kHz, 120 V 60 Hz mains)

 

MPX1200

 

2 ohm load/channel:

 

1600 W

 

4 ohm load/channel:

 

1200 W

 

8 ohm load/channel:

 

800 W

 

4 ohm bridge:

 

3200 W

 

8 ohm bridge:

 

2400 W

 

TYPICAL MIDRANGE OUTPUT POWER: (Typical 1 kHz @ 1% THD, 120 V 60 Hz mains)

 

 

2 ohm load:

 

1640 W

 

4 ohm load:

 

1340 W

 

DISTORTION @ RATED POWER:

 

 

1 kHz, 8 ohm load (typical):

 

0.020%

 

1 kHz, 4 ohm load (typical):

 

0.025%

 

20 Hz - 20 kHz, 8 ohm load:

 

0.15%

 

20 Hz - 20 kHz, 4 ohm load:

 

0.2%

 

Net Weight:

 

29.5 kg (65 lbs)

 

Shipping Weight:

 

33.1 kg (73 lbs)

 

 

Frequency Response:

20 Hz to 20 kHz, ±0.15 dB

Damping Factor:

Greater than 200 at 8 ohms

Dynamic Headroom:

2.5 dB at 4 ohms

Noise:

100 dB below rated output (20 Hz to 20 kHz)

Sensitivity:

1 Vrms for rated power (8 ohms)

Input Impedance:

10 kOhms unbalanced, 20 kOhms balanced

CONTROLS:

Front Panel:

AC switch, Ch 1 & Ch 2 Gain (detents @ 0 dB, -2 dB, -4 dB, -6 dB, -8 dB, -12 dB, -14 dB, -18 dB, -24 dB, infinity), Ch1 & Ch 2 High Pass Filter Switches

 

Rear Panel:

 

Slide switch for Stereo, Dual Mono (paralleled inputs) or Bridged Mono input and output configurations

 

INDICATORS: (each channel)

Power:

Green LED

Signal Present:

Green LED

Clip:

Red LED

Protect:

Red LED

CONNECTORS: (each channel)

Input:

XL-type 3 pin (pin 2 high)/6.3 mm (1/4 in) TRS combination connector and removable barrier strip with separate chassis ground terminal

Output:

Binding Posts, touch resistant, accepts dual banana plugs and up to #8 AWG bare wire

COOLING:

Rear-to-Front Airflow (all models)

 

 

MPX1200:

Continuously variable speed fan

 

 

Amplifier Protection:

Full short circuit, open circuit, ultrasonic, and RF protection, current limiting, thermal muting; stable into reactive or mismatched loads. MPX1200 additionally has thermal/clip limiting

Load Protection:

On/off muting, DC-fault load grounding relay with internal fault fuses. MPX1200 additionally has clip limiting.

Output Circuit Type:

Complementary linear, high-efficiency outputs: 3-step on MPX1200, 2-step on MPX600, no-step on MPX300

Power Requirements:

100V, 120V, 220V or 230V AC, 50-60 Hz (not user configurable)

Dimensions: (HxWxD)

133 x 483 x 408 mm (rack depth 404 mm) 5.25 x 19 x 16.1 in (rack depth 15.9 in)

Thanks for looking , stay well

John A