VFE Klein Bottle V2 2022 - Present - Graphic
A VFE Klein Bottle V2, in mint condition! This particular one sports the "Kelp Forest" graphic in a baby blue colourway. Ships in its original box, with all paperwork/candy included.
From the manufacturer:
Klein Bottle Controls
PRE - Sets the volume of the signal going out each FX loop.
MIX - Sets the volume of the signal going back into the final mix.
HPF - Sets the corner frequency of a 12dB/octave high pass filter. Turn this control fully counterclockwise to flatten out the bass response. This filter is before the loop.
LPF - Sets the corner frequency of a 12dB/octave low pass filter. Turn this control fully clockwise to flatten out the treble response. This filter is before the loop.
6 dB / 12 dB - Selects the slope the HPF & LPF filter circuits. 6 dB per octave yields a gentler frequency cut, whereas 12 dB per octave yields a sharper cut that is better for isolating specific frequency ranges on each loop.
LOOP X - Sets the amount of signal sent from one loop's return to another loop's send. The number specifies which loop is receiving the signal.
0° / 180° - Phase inversion switch to correct (or create) phasing issues.
MASTER - Sets the overall output of the pedal.
NOTE - The MASTER knob does not go fully silent when you turn it all the way counterclockwise. Its primary purpose is to let you quickly adjust the overall volume without needing to adjust the 3 mix knobs, and a fully silent volume control would have made the switching & output stage needlessly complicated. The MASTER knob is technically active even when the pedal is in bypass and will adjust the volume of any decaying trails...but will keep the input signal at unity while in bypass.
DRY - Sets the amount of the original, dry input signal fed into the final mix.
TRAILS - This toggle switch selects what parts of the circuit remain on when an effect is turned off. Set to "SENDS" to keep all the LOOP X controls active at all times. Set to ALL to have both the MIX output and LOOP X controls active continously. The middle position turns off everything connected to that loop when not active. In all positions, the LOOP X and MIX controls remain active when you hold the footswitch down, allowing for more natural decay of time-based effects.
PRE / POST - Places the FX loops before (PRE) or after (POST) the filter section. In the PRE section, the filters can be used to sculpt the character of the effect(s) in the loop, especially gain pedals. In the POST section, the filters affect the signal each time they pass back through the feedback circuits.
PRE-GAIN - Internal pre-gain trimpots let you adjust signal strength to work well with a variety of instruments and effects.
IMPED - Sets the input impedance of the Klein Bottle. Set to about 1M-ohm by default, which is great for a variety of passive instruments. If you use exclusively active instruments (like synths), input impedance can be lowered to reduce the small amount of thermal noise that comes from this resistance (which can build up after multiple feedback loops).
LED - Internal makeup gain trimpots to set the brightness of each LED.
Protezione di Reverb per gli acquirenti
Reverb ti protegge nel caso in cui il tuo articolo venga perso, danneggiato o non corrisponda alla descrizione. Basta segnalare eventuali problemi entro 7 giorni e ti aiuteremo a ottenere il rimborso completo.Scopri di più sulla Protezione di Reverb per gli acquirenti.
| Pubblicato | 10 ore fa |
|---|---|
| Condizione | Eccellente (Usato) Gli articoli "Eccellenti" sono quasi completamente privi di difetti e altri difetti visivi e sono stati suonati o utilizzati con la massima cura.Scopri di più |
| Marchio | |
| Modello |
|
| Finish |
|
| Anno |
|
| Formato pedale |
|
Le informazioni sulla sicurezza del prodotto sono disponibili qui.


