Irmo, SC, United States
About this listing
The Royer dBooster2 Dual In-Line Signal Booster is two channels of everything we love about the original dBooster, PLUS both channels double as high-quality, super clean DI’s for electric guitars and bass! When used as a signal booster, both channels of the dBooster2 increase the level of passive low-output ribbon and dynamic microphones with a minimum of distortion or coloration. Designed for professional applications, each dBooster2 channel offers two levels of clean gain boost: 12dB or 20dB, selectable by a front panel switch. The dBooster2’s Class A input presents a high source impedance to microphones, minimizing loading (damping) and improving headroom. By utilizing the 12/20dB gain switch, optimum balance between gain and headroom can be achieved for a variety of uses. The dBooster2’s low-impedance output is an increased microphone-level signal that can drive a digital interface directly or a standard microphone preamplifier. It also minimizes signal loss on long cable runs. When used as a DI for unbalanced guitar level sources, the dBooster2 provides either 0dB or 8dB of gain, selectable from the front panel switch. The single ended high-impedance (230K-Ohm) DI input maintains headroom and gain regardless of load, with minimal distortion or coloration. The dBooster2 gives excellent results with Royer 's, 's and stereo 's. It also smokes on 's and other dynamic mics! The dBooster is built in the USA and also available as a single channel version, the . Royer dBooster2 Dual In-Line Signal Booster Features 12dB and 20dB gain stages in Mic mode 0dB or 8dB gain in Hi-Z DI mode High input impedance Balanced Low output impedance Rugged case construction Ultra-low noise performance Ultra-low distortion Wide frequency bandwidth Safe for use on all ribbon mics Increases headroom at the preamp Provides true electrical isolation Protects ribbon mics from phantom-power Minimizes mic loading Capable of driving difficult loads, such as mic splitters and vintage style preamps, without increased distortion or loss of gain Royer dBooster2 Dual In-Line Signal Booster Applications Miking any low-volume sound source (acoustic instruments, vocals, etc.) Recording direct to a DAW interface Use on long cable runs to retain sound quality DI for direct electric guitar, electric bass, and other instruments Royer dBooster2 Dual In-Line Signal Booster Specifications Gain: switchable 12dB or 20dB in Mic mode, switchable 0dB or 8dB in DI mode THD+N: @ 20dB Gain = .0015%, -25dBu input signal, 1.3Vp-p output signal @ 12dB Gain = .001%, -6dBu input signal, 3.66Vp-p output signal IM Distortion: @ 20dB setting, < .002% @ 800mV output, @ 12dB setting, < .005% @ 2.6volts outpu Self-Noise: referred to -48dB re. 1V/Pa 20dB setting < 11dBa, 12dB setting < 15dBa Headroom: referred to -48dB re. 1V/Pa and 4mV/Pa 20dB setting: 127dB, 12dB setting: 120dB Frequency Response: 20Hz-20kHz +/- .25dB Input Impedance: 3.6K-Ohm in Mic mode, 270K-Ohm in DI modeOutput Impedance: (at 20dB setting) 300-Ohms Current Draw: approximately 5mA at zero signal and 7.5mA at full output Input and Output Connections: Balanced XLR: (Pin 1 Ground, Pin 2 Signal Hot, Pin 3 Signal Cold), HI-Z (DI) ¼-inch unbalanced, tip signal HOT. Power: 48-Volt phantom Dimensions: 3.875” (98.425mm) L X 3.875” (98.435mm) W X 1.75” (44.45mm) H Weight: 10.2 oz (289g) Warranty: The dBooster2 is covered by a one-year warranty. This warranty covers parts and labor but does not cover damage as a result of misuse or abuse Royer dBooster2 Dual In-Line Signal Booster Includes Royer dBooster2 Dual In-Line Signal Booster dBooster2 Cutsheet dBooster2 User Guide Manufacturer Warranty
PriceA$520.83
+ A$147.74 Shipping
A$89.53 shipping when combined
14-Day Return Policy
Enjoy peace of mind with your new gear
