Soundcraft 6000 input strips - tested & working. A lot of four strips each with classic British mic pre / EQ etc. Comes supplied with one four channel input panel (with mic in / line in / direct out & insert), main interconnecting ribbon cable & power supply interface PCB for connecting the ribbon to suitable power supply. All the jacks are standard 1/4” and the direct outs are unbalanced.

Apart from a suitable power supply (which you will need to source), these are ready to work as standalone mic pre / EQ strips (using the ‘line out‘ on each strip).

I can also supply a different power supply interface PCB (shown in the last picture) for an additional cost. This connects to the ribbon cable, supplies necessary power rails but also takes the mix left & right buss, feeds them into two virtual earth mix amps each of which drives a small power amp & two output transformers (giving you balanced mix left and right output with plenty of transformer colour). If you require this PCB please get in touch to discuss. Additionally I could potentially design a similar board to balance each of the ‘line outs’ & add some transformer colour to those - please contact me to discuss….

I have tested each strip and they all work / pass audio. I haven’t tested the aux sends or all the routing as none of that is connected when used as standalone mic pre / EQ strip. I’ve not re capped them as I tested a few of the electrolytics from places where there under most stress (randomly selected strips) & they all measured fine. If you were to re cap them, it would need to be with very high quality caps to make a positive difference IMO.

Please note: while I have tested each strip & cleaned anything that needed it they are old strips so there might be a slightly noisy pot or switch (which is to be expected with desks of this age).

They require a dual rail regulated power supply with ideally +/-17v rails but would probably run off +/-15~16v (with a slight reduction in headroom). If you want to use the phantom power, you will also need your power supply to have a regulated +48v rail (With the 0v connected to the 0v / ground on the supplied PCB). The four strips pull about 170mA idle (at +/-17v).

Due to the input panel being 4 channel I’ll only sell them in multiples of four (unless you don’t need the input panel). I will shorty be adding an ‘8 strip‘ version of this listing. I have hundreds of these & other vintage soundcraft strips, including sidecars, baby mixers, 8 chan Mic Pre & EQ, summing mixers etc which I will be listing this year.

The strips do have some cosmetic imperfections (mostly some scratches / marks etc) & some slight surface rust to the washers under the ‘pot nuts’ but generally there in pretty good condition for there age. Please see all the photos.

Any questions please ask.

Dieser Artikel wird verkauft "wie beschrieben"

Dieser Artikel wird verkauft "wie beschrieben" und kann nicht retourniert werden, es sei denn er kommt anders als beschrieben oder fotografiert an. Artikel müssen im Originalzustand mit allen gelieferten Teilen und Zubehör in ursprünglicher Verpackung zurückgesendet werden.Mehr erfahren

Beworbene ähnliche Inserate













Inseriertvor 9 Monaten
ZustandSehr gut (Gebraucht)
Artikel im Zustand Sehr gut können ein paar Makel oder Macken haben, aber funktionieren einwandfrei und sind ingesamt gut erhalten.Weitere Informationen
Marke
Modell
  • 6000 Input Strips
Farbe
  • Black
Kategorien
Jahr
  • ??
Hergestellt in
  • Vereinigtes Königreich

Möglicherweise sind hier Informationen zur Produktsicherheit verfügbar.

Über den Verkäufer

RCH Audio Engineering

St Albans, Vereinigtes Königreich
Mitglied bei Reverb seit:2023

Reverb-Schutz

Einfache Rücksendungen, sichere Transaktionen, Support von Experten

Weitere Informationen

Sichere Zahlung

Reverb Gives

Mit deinen Käufen unterstützt du Programme zur Förderung Jugendlicher, damit sie das Equipment erhalten, das sie zum Musizieren brauchen.

Ups, sieht aus, als hättest du etwas vergessen. Bitte prüfe die rot hervorgehobenen Felder.