LOOP-MASTER PEDALS HUGHES & KETTNER FS-2 STYLE FOOTSWITCH

A compact, rugged alternative to the Hughes & Kettner FS-2 for compatible amplifiers.

The Loop-Master Pedals Hughes & Kettner Style Footswitch provides two independent latching footswitch functions through a single 1/4" TRS connection.

Depending on your amplifier, the two switches can control functions such as channel selection, boost, effects, FX loop and other amp-specific functions.

Two switches. One TRS cable. No power required.

WHAT IT DOES

• FS-2 style dual amp footswitch

• Two latching footswitches

• Single 1/4" TRS connection

• Controls two functions on compatible Hughes & Kettner amplifiers

• Functions determined by the connected amplifier

• Completely passive operation

• No battery or power supply required

• Premium TRS jack

• Compact pedalboard-friendly enclosure

• Handcrafted in the USA by Loop-Master Pedals

COMPATIBLE APPLICATIONS

Designed for compatible Hughes & Kettner amplifiers that accept the FS-2 or equivalent standard two-button latching TRS footswitch.

Depending on the amplifier, functions can include:

• Clean / Lead channel switching

• Channel selection

• Lead Boost

• FX Loop On / Off

• Internal Effects On / Off

• Reverb

• Mute

• Other amp-specific functions

The amplifier determines what each switch controls.

TUBEMEISTER DELUXE 20

On the Hughes & Kettner TubeMeister Deluxe 20, the two-button footswitch connection controls:

• Channel – Clean / Lead

• Lead Boost – On / Off

The amp uses a standard stereo/TRS footswitch connection with one function on Tip and the other on Ring.

OTHER HUGHES & KETTNER AMPS

Hughes & Kettner uses the FS-2 with a variety of amplifiers, but the functions are not always the same.

For example, depending on the amplifier, an FS-2 style controller may operate:

• Channels

• Boost

• Effects

• FX Loop

• Reverb

• Mute

This makes the controller useful with a wide range of compatible Hughes & Kettner amps while keeping the footprint much smaller than a conventional factory footswitch.

COMPACT DESIGN

At only 3.63" × 1.5", this controller takes up very little pedalboard space.

It's a great choice when you want the functionality of a two-button amp footswitch without dedicating a large section of your pedalboard to the factory controller.

HOW IT WORKS

Connect the Loop-Master Pedals footswitch to the compatible amplifier using a standard 1/4" stereo/TRS cable.

Each footswitch operates one of the two control connections carried by the TRS cable.

Press a switch and it latches into its alternate state.

Press it again and it returns to the previous state.

No programming or setup is required in the footswitch itself.

LATCHING SWITCHING

This controller uses two LATCHING footswitches.

These are not momentary switches.

Your amplifier must support standard latching contact switching through its 1/4" TRS footswitch connection.

DIMENSIONS

• 3.63" × 1.5" × 1.06"

• 9.22 × 3.81 × 2.69 cm

• 92.2 × 38.1 × 26.9 mm

POWER

No power required

CONNECTION

• 1 x 1/4" TRS control jack

A standard stereo/TRS cable is required.

TRS cable is not included.

CONSTRUCTION

• Two heavy-duty latching footswitches

• Premium TRS jack

• Rugged aluminum enclosure

• Completely passive operation

• Compact pedalboard-friendly footprint

• Handcrafted in the USA by Loop-Master Pedals

IMPORTANT COMPATIBILITY NOTE

This is a Loop-Master Pedals product designed for compatible Hughes & Kettner amplifiers that use a standard two-button latching TRS footswitch such as the Hughes & Kettner FS-2.

It is not manufactured by or affiliated with Hughes & Kettner.

Footswitch functions vary between amplifier models.

This controller is not intended to replace proprietary MIDI or multi-function foot controllers.

If you're unsure whether your amplifier is compatible, contact us with the exact Hughes & Kettner model before ordering.

TRS cable not included.