Genelec 4010A 2-Way Active Installation Speaker (White)

Overview

The Genelec 4010A is a compact 2-way active loudspeaker for fixed indoor installations. Its 3 in cone woofer and 3/4 in metal dome tweeter each run from their own 25 W Class D amplifier. The amplifiers, active crossover and driver protection are built into the die-cast aluminium enclosure, so no external power amplifier is needed. Rear-panel switches adjust the bass and treble to suit the room and the mounting position.

Key Features

• Active design: Drivers, power amplifiers, active crossover filters and protection circuitry are all inside the speaker.
• MDE enclosure: The recycled die-cast aluminium Minimum Diffraction Enclosure is shaped to reduce edge diffraction.
• DCW waveguide: Genelec's Directivity Control Waveguide controls dispersion and reduces early reflections from nearby surfaces.
• Room response controls: Treble Tilt and Bass Tilt switches, with Bass Tilt cutting the bass by 2, 4 or 6 dB for placement near a wall or in a corner.
• Sensitivity switch: Input sensitivity can be set to normal or -10 dB.
• ISS Autostart: The speaker drops to standby, typically under 0.5 W, after about an hour without signal and wakes when signal returns. A rear switch disables it.
• Balanced input: Audio connects through a 3-pin Euroblock plug.
• Mounting options: A 3/8 in UNC thread on the base fits a standard microphone stand, three pairs of rear threaded holes accept Omnimount, VESA and Sanus brackets, and the included wall bracket hangs the speaker at two angles.
• Finishes: Black, white or RAW, which is unpainted recycled aluminium with a slightly different look on every enclosure.

Specifications

• Type: 2-way active loudspeaker, bi-amplified
• Woofer: 76 mm (3 in) cone
• Tweeter: 19 mm (3/4 in) metal dome
• Frequency response (±2.5 dB): 74 Hz - 20 kHz
• Low cutoff (-6 dB): 67 Hz
• High cutoff (-6 dB): 25 kHz
• Max short-term SPL (1 m): ≥96 dB
• Max long-term SPL (1 m): ≥91 dB
• Max peak SPL per pair (1 m): ≥105 dB
• Self-generated noise (1 m, A-weighted): ≤5 dB
• Harmonic distortion (80 dB SPL, 1 m): ≤3% (70-400 Hz), ≤0.5% (above 400 Hz)
• Crossover frequency: 3.0 kHz
• Amplifiers: 25 W bass + 25 W treble, Class D
• Input: Balanced, 3-pin Euroblock
• Input level for 100 dB SPL at 1 m: -6 dBu
• Sensitivity switch: Normal or -10 dB
• Bass Tilt: 0 to -6 dB @ 100 Hz in 2 dB steps
• Mains voltage: 100-240 V AC, 50/60 Hz
• Power consumption: ≤0.5 W standby (ISS), ≤5 W idle, 30 W full output
• Enclosure: Die-cast aluminium, reflex port
• Dimensions (H x W x D): 181 x 121 x 115 mm (7 1/8 x 4 3/4 x 4 1/2 in)
• Weight: 1.5 kg (3.3 lb)
• Operating environment: Indoor, 15 to 35 °C, 20 to 90% relative humidity
• Finish: White

In the Box

• 4010A installation speaker
• 3-position terminal block (audio input plug)
• Mains cable, 1.8 m
• Simple bracket (keyhole wall mount)
• Mounting screw set
• Operating manual