Los Angeles, CA, United States
About this listing
Peavey IPR2 3000 Power Amplifier 2-Channel Power Amplifier, 840W RMS/ch at 4 ohms, with built-in Crossovers, Speaker Protection, lightweight 7.9 lbs chassisUltra-lightweight power amplifier provides high audio resolution and extreme efficiency.The IPR2 3000 power amplifier is designed for years of reliable, flawless operation under rigorous use. The groundbreaking IPR2 Series utilizes an advanced design that allows Peavey engineers to dramatically reduce weight while increasing output power, reliability, and thermal efficiency. IPR2 Series amplifiers are designed with a resonant switch-mode power supply and a high-speed class D topology that yields the highest audio resolution and efficiency available.This revolutionary amplifier offers the sonic superiority and unsurpassed reliability for which Peavey is famous, in an extremely efficient and lightweight design. Advanced technology and extensive protection circuitry allow operation with greater efficiency into difficult loads and power conditions. The DDT (Distortion Detection Technique) circuitry ensures trouble-free operation into loads as low as 2 ohms. DDT protects drivers and ensures that sonic integrity is maintained, even in extreme overload conditions. The IPR2's high-efficiency design allows the amplifier to operate at very low temperatures and does not require massive heat sinks to cool.Features:2-channel independent fourth-order Linkwitz-Riley crossoversDDT protectionRevolutionary IPR class D topologyCombination XLR and 1/4" inputsSpeakon output connectorsLightweightTwo-pole combination twist lock and 1/4" (6.3mm) phone plug outputsIndividual signal patch 1/4" (6.3mm) jacks on each channelStandup, LED power present indicationDetented input controls1750w at 2 ohms950w at 4 ohms525w at 8 ohmsIndividual signal pass 1/4" jacks on each channelSPECIFICATIONS:Rated Watts 2ch x 2 ohms: 1750 watts 20ms repetitive burst / 1450 watts 1% THD both ch. driven @ 1kHzRated Watts 2ch x 4 ohms: 950 watts 20ms repetitive burst / 900 watts 1% THD / 815 watts 0.2% THD, both ch. driven @ 1kHzRated Watts 2ch x 8 ohms: 525 watts 20ms repetitive burst / 500 watts 1% THD / 430 watts 0.15% THD, both ch. driven @ 1kHzMinimum Load Impedance: 2 ohmsMaximum RMS Voltage Swing: 70VFrequency Response: 20Hz - 22kHz; +/-.05dB @ 4 ohms20Hz - 20kHz 2ch x 2 ohms: <0.15% @ 1,200 watts 20Hz to 3kHz, decreasing to 1,100 watts @ 20kHz, both ch. driven20Hz - 20kHz 2ch x 4 ohms: <0.15% @ 650 watts 20 Hz to 20 kHz, both ch. driven20Hz - 20kHz 2ch x 8 ohms: <0.15% @ 375 watts 20 Hz to 20 kHz, both ch. drivenInput CMRR: > - 76dB @ 1kHzVoltage Gain: x 75 (+37dB)Crossover: 100Hz switchable 2nd order high pass and 3rd low pass per channelCrosstalk: > -68 dB @ 1 kHz @ 400 watts @ 8 ohms Hum and Noise: > -101.5 dB, "A" weighted referenced to rated power @ 4 ohms Slew Rate: > 12V/μs Damping Factor (8 ohms): > 215:1 @ 20 Hz - 1 kHz @ 8 ohmsInput Sensitivity: .775 volts +/- 3% for 1kHz 4 ohm rated power, .73 volts +/- 3% for 1kHz, 2 ohm rated power Input Impedance: 15kOhms, balanced and 7.5k ohms unbalancedCurrent Draw @ 1/8 power in VA (watts): 960 (535) @ 2 ohms, 615 (315) @ 4 ohms, 400 (200) @ 8 ohmsCurrent Draw @ 1/3 power in VA (watts): 2065 (1360) @ 2 ohms, 1215 (735) @ 4 ohms, 740 (420) @ 8 ohmsIdle Consumption: 160VA, 75 watts Cooling: Temperature dependent variable speed 80mm DC fanControls: Two front panel attenuators, crossover select switch for HPF, Normal and LPF Indicator LEDs: Five LED indicators per channel: Active, Signal, DDT, Temperature and DCProtection: Thermal, DC, subsonic, incorrect loads, under and over voltage Connectors: Dual combination 1/4" & XLR, dual male XLR input thru, two twist lock connectors Construction: 0.062" aluminumDimensions: 3.5" x 19" x 10.5" behind front panel + 0.6" for handleWeight: 5.62kg (12.4 lb.* )
Price$649.95
Free Shipping
Free Shipping
from Los Angeles, CA
14-Day Return Policy
Enjoy peace of mind with your new gear
