Peavey Peavey IPR2™ 7500 Lightweight Power Amp 2026

The Peavey IPR2™ 7500 delivers high-output, two-channel amplification in a lightweight design. Its high-speed Class D topology and resonant switch-mode power supply combine efficient power delivery with reduced weight and heat, making it easier to bring serious power to your setup.

Built for demanding use, the IPR2 7500 supports speaker loads as low as 2 ohms. Peavey’s DDT™ (Distortion Detection Technique) circuitry helps protect drivers and preserve sonic integrity during overload conditions, while additional protection circuitry guards against thermal, DC, subsonic, load and voltage issues.

Each channel offers selectable 100Hz high-pass, full-range or low-pass operation, with front-panel level controls and LED status indicators. Three temperature-controlled, variable-speed fans manage cooling.

Rated Watts 2ch x 2 ohms4750 watts 20ms repetitive burst / 3750 watts 1% THD both channels driven @ 1kHz.

Rated Watts 2ch x 4 ohms2800 watts 20ms repetitive burst / 2450 watts 1% THD / 2020 watts 0.15% THD, both channels driven @ 1kHz.

Rated Watts 2ch x 8 ohms1550 watts 20ms repetitive burst / 1425 watts 1% THD / 1200 watts 0.15% THD, both channels driven @ 1kHz.

Minimum Impedance2 ohms

Maximum RMS Voltage Swing124 volts

Frequency Response20Hz - 25kHz; +0dB, -3dB

20Hz - 20kHz 2ch x 2 ohms<0.5% @ 3280 watts 20Hz to 4kHz, decreasing to 3000 watts @ 20kHz, both channels driven.

20Hz - 20kHz 2ch x 4 ohms<0.15% @ 2000 watts 20Hz to 20kHz, both channels driven.

20Hz - 20kHz 2ch x 8 ohms<0.15% @ 1200 watts 20Hz to 20kHz, both channels driven.

Input CMRR> - 75dB @ 1 kHz.

Voltage Gainx 40 (+32dB)

Crossover100Hz switchable 2nd order high pass and 3rd low pass per channel.

Crosstalk> -85dB @ 1kHz @ 1000 watts power @ 8 ohms.

Hum and Noise> -106dB, “A” weighted referenced to rated power @ 4 ohms.

Slew Rate> 12V/μs

Damping Factor (8 ohms)> 200:1 @ 20Hz - 1kHz @ 8 ohms

Input Sensitivity2.25 volts +/- 3% for 1kHz 4 ohm rated power, 2.195 volts +/- 3% for 1kHz 2 ohm rated power

Input Impedance20 kilohms, balanced and 10 kilohms unbalanced.

Current Draw @ 1/8 in VA (watts)2210 (1440) @ 2 ohms, 1550 (950) @ 4 ohms, 982 (560) @ 8 ohms

Current Draw @ 1/3 in VA (watts)4260 (3150) @ 2 ohm, 3120 (2160) @ 4 ohms, 1890 (1200) @ 8 ohms

Idle Consumption250VA, 120 watts.

Cooling3 temperature dependent variable speed fans.

Controls2 front panel attenuators, crossover select switch for HPF, Normal and LPF

Indicator LEDsFive LED indicators per channel: Active, Signal, DDT, Temperature and DC

ProtectionThermal, DC, subsonic, incorrect loads, under and over voltage

ConnectorsInputs: Dual combination 1/4” XLR, Outputs: Dual 1/4” thru, one 2-pin & one 4 pin twist-lock connector

Construction0.062” thick aluminum

Dimensions3.5”x19”x 17” behind front panel + 0.6” for handle

Net Weight6.61kg (14.6lbs.*)

Gross Weight8.34kg (18.4lbs.)

Rated power readings made with BW: 20 Hz to 22 kHz. All power measurements made @ 120 VAC or 240VAC.
2 ohm steady state sine wave power is time limited by circuit breaker.
Bridge operation is not possible.
*Net Weight does not include power cord.