Inwood, NY, United States
About this listing
Authorized Crown Audio Dealer!
Input EQ
6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed.
Crossover Filters
Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes ± 15 dB bandpass gain and polarity control.
Output EQ
8 parametric filters per channel with adjustable Q, ±15 dB boost/cut. This 8-filter EQ section can be bypassed.
Delay
For signal alignment of driver; 50 mS of total delay.
SubHarmonic Synth
Takes the low-frequency content of the input signal and "synthesizes" a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect. New: Users now have control over frequency, gain, and filter type.
Peakx™ Plus Limiter
User defeatable limiter that allows users to control Threshold, Attack, and Release times.
Presets
50 total presets, 49 of which are user-definable.
Features
XTI4002 2 Channe Power Amplifier
RMS Power @ 2 Ohm: 1600 Watt x 2
RMS Power @ 4 Ohm: 1200 Watt x 2
RMS Power @ 8 Ohm: 650 Watt x 2
Bridge RMS Power @ 8 Ohm: 2400 Watt x 1
Bridge RMS Power @ 4 Ohm: 3200 Watt x 1
Peak Plus Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release
Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning
3 User-defined fan mode controls - normal, early and fullspeed - for matching fan performance to a specific application
New system monitoring provides software visibility of AC line voltage and power supply temperature
Integrated cast-aluminum handles for easy handling and enhanced durability
Locking power cord clip provides a secure connection between the amplifier and power cord
Updated HiQnet Band Manager and System Architect control software
Increased number of presets to a total of 30; 29 of which are user definable
Performance
Sensitivity (for full rated power at 4 ohms): 1.4 Vrms
Frequency Response (at 1 watt, 20 Hz - 20 kHz): +0 dB, –1 dB
Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms): 100 dB (A weighted)
Total Harmonic Distortion (THD): < 0.5%
Damping Factor 20 Hz to 1 kHz: > 500
Crosstalk (below rated power): 20 kHz - 1 kHz: > 70 db
Input Impedance (nominal)
Balanced: 20k ohms
Unbalanced: 10k ohms
Maximum Input Signal: +22 dBu typical
AC Line Voltage and Frequency Configurations: 100 VAC, 120 VAC, 220-240 VAC 50/60 Hz
AC Line Current(120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch): 10.5A; no more than 38W at idle
Operating Temperature: 0°C to 40°C at 95% relative humidity (non-condensing)
Controls
Level: Two front-panel rotary level controls, one for each channel
Power Switch: On/Off switch applies AC power to the amplifier
Sel/Prev/Next Buttons: Three buttons near the LCD screen that are used to access menu items and front panel lockout
LCD Screen: Backlit liquid crystal display that shows preset and processing status
Indicators
Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs)
–10 Indicator: Green LED flashes when output signal exceeds -10 dB below clip
–20 Indicator: Green LED flashes when output signal level exceeds -20 dB below clip
Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion
Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions
Power Indicator: Blue LED illuminates when the amplifier has been turned on and has power
Input/Output
Input Connectors: XLR, one per channel
Link/Out Connector: Loop-thru signal from input connector for linking another amplifier, one per channel
Output Connectors: Two Neutrik® Speakon® NL4MP output connectors. Channel-1 Speakon® is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon® connectors)
HiQnet™ USB Connector: Type B, connects to HiQnet™ network
Constructions
Chassis: Steel
Front Panel: Cast-aluminum
Cooling: Proportional speed fan with front-to-rear airflow
Dimensions (WxHxD): 19" x 3.5" x 12.25"
Net Weight: 18.5 lbs (8.4 kg)
Shipping Weight: 21.5 lbs (9.8kg)
for the Owner's Manual
Price$1,659
Free Shipping
Free Shipping
from Inwood, NY
14-Day Return Policy
Enjoy peace of mind with your new gear
