Similar Listings

Grundig GDM-121 Dynamic Microphone s/n 06712 late 50's made in West Germany ( Sennheiser MD21 )

Excellent
$371.57
+$47.86Shipping
$15.11 shipping when combined
Listing Sold
Shipped From
BEP Boutique Effect Pedals
Rotterdam, Netherlands
1,490
Sales
2000+
Joined Reverb
2014
Preferred Seller
Quick Responder
Quick Shipper

About This Listing

Grundig GDM-121 Dynamic Microphone late 50's made in West Germany with box in excellent condition and full working order. Jack is replaced with 3 XLR plug.
Quoted from Trashblitz website ; Grundig GDM-121 Behold one of the foundational pillars of : The Grundig GDM-121, 1950s German vintage gold deluxe, and in all its glory quite probably responsible for this website. It is to this day the only gold coloured microphone we own, and it has such a cute little metal table stand with the Grundig four-leaf clover on it! And, more importantly, it was one of the first “vintage” microphones we acquired that did not simply sound old, funny or broken, and it piqued our interest in a very special way: It sounded fantastic, but there was buzz and hum and all sorts of unpleasant background noises mixed into the signal – and here my quest to  began. I found out that the GDM-121 is a high-impedance version of the Sennheiser MD21, a dynamic omnidirectional reporter microphone which is still being manufactured with only minor design updates, more than 60 years after its release in 1953.

In terms of usefulness, this means that it is 100% functionally equal to the MD21, which was used as a reporter mic and in broadcasting. It has many advantages for these purposes – almost no handling noise, no proximity effect, incredibly sturdy (there was supposedly a show on the Sennheiser stage on some fair in the 1950s where an MD21 was dragged up and down a flight of stairs for hours, and it was still operational after this treatment). Since it was developed for vocal applications mainly, it has a presence boost above 3kHz and can withstand really high SPL. Much like with its cardioid sibling, the MD421, it’s virtually impossible to get a distorted signal out of this mic.

In the studio, it can be used as a soft, jazzy kick drum mic, on guitar cabinets and on many instruments where you want to capture a mellow and natural ambient sound without very detailed transients or highs. This is because it is a large-diaphraghm dynamic omni, and as such probably unique in its properties even in most serious studio microphone collections.

Anyway, the GDM 121 has a built-in impedance transformer (as has the Sennheiser MD21 HN, by the way) which has to be removed in order to use it with contemporary recording equipment and integrate it in one of said collections. Further research showed it was designed for unbalanced tape recorder input, so to convert it to XLR, I feared I even had to bridge pins. Luckily, all unbalanced GDM-121 models I have opened so far actually used balanced cable which only needed to be connected to the body and wired correctly. Now, opening the GDM-121 or the Sennheiser MD21 is a much harder task than I would have imagined, and I’m very glad I found  with detailed instructions. I’ll give you a rough guide in my own words: How to open up and convert the Grundig GDM-121 to XLR
  1. First, you’ll have to gently hammer the metal pins on both sides of the microphone grille into the body, using a slim steel nail, an awl or something similar. If you have a tiny hammer or a non-metal mallet, use it. Don’t lose those pins, or you won’t be able to close the microphone housing anymore!
  2. Take out the microphone capsule. Inside, you’ll find the high-impedance transformer, snugly lodged inside a plastic compartment in the capsule holder.
  3. Bypass the transformer, or desolder all the wires leading to and from it and simply rip it out, your GDM-121 will not miss it.
  4. Connect the textile-coated wires directly to the capsule. Make a note which colour went to + and which one to -, so you can later connect them to the XLR plug correctly.
  5. Attach the ground to the housing. I’ve had no luck soldering inside the microphone’s body, so maybe try scratching it with a file before soldering, or use glue or other mechanical ways of attaching it if you run into similar problems.
  6. Put the capsule back in place and close the mic. This can be quite hard, either you manage to do it alone with the help of a vice, or you get somebody to press the capsule and grille into the body while you try and hammer in the pins.
  7. Cut off or open up and desolder the DIN plug. I recommend to do it this way, the soldering on these mics is usually very neat and you can directly use the already stripped wires for your male XLR plug. Have a look at the notes you made and complete your wiring. 1 is ground, 2 is your hot (+) cable and 3 your cold (-) cable.
  8. And you’re done!

Norbert also mentions that it’s possible to insert a male XLR jack into the tail end of the mic by opening a screw that sits beneath the connection thread for the stand – but to be honest, I never found that screw. I suppose you’ll have to scratch off some paint to spot it. If you manage to find and open it, you can remove the small aluminium cone that holds the cable in place, remove it and insert an XLR jack – that’s quite some mod! As I said, I never managed or bothered to do that, but it sounds intriguing.

There are many different models of the GDM-121, the oldest being the gold coloured ones with the flat grille, sometimes also labeled Grundig MD 121 or Grundig GDM 12 – obviously, they couldn’t really decide how to call it. The one on the picture is a later model, gold with round grille, and there are white and grey ones, too. Also, if you are very lucky, you can find one with DIN small tuchel connector instead of a fixed cable, which has the additional benefit of no built-in transformer. These are ready to go immediately, much like the Telefunken MD21 and the Labor W MD21 (the direct predecessor – Labor W was Sennheiser’s former company name), which have small or large tuchel connectors – both are even closer to the Sennheiser version than the Grundig.

Specs!

  • Frequency range: 40 – 18,000 Hz
  • Capsule impedance: 200 Ohm
  • Polar pattern: Omnidirectional
Quoted in German from Norbert Büchner's website ;

Du wurdest wegen Tipps zum GDM 121 weitergeleitet oder bist über die Internetsuche hier her gelangt. Frage wie sieht das Mikrofon auf der Nichteinsprechseite aus? Wenn da nur ein Kabel rauskommt, was ich auch vermute, dann reicht es nicht aus, nur einen Stecker neu anzulöten!!!!!

Dieses Mikro GDM 121 ist die Variante für hochohmige  Eingänge von Röhrengeräten, also hat das Mikro einen hochohmigen Anschlusswert. Wie gehst du vor: die Schlicht Variante

zuerst die Splinte am Mikrofonkopf mit einem feinen Austreiber (gehärtet und mit Schonhammer, Gummihammer) nach Innen austreiben. Es kann ein Bilderhakennagel oder ähnliches sein. Achtung Splinte nicht verlieren, die brauchst du für den Zusammenbau. Im Innern findest du die Sprechkapsel und den Spar-Trafo für das hochohmig-Machen des Mikros. Den Trafo umgehst du in der Verkabelung und schließt a und b jeweils an ein abgehendes Kabel an. Die Schirmung muß dann irgenwie an das Gehäuse gezaubert werden.

Edel wird es, wenn du das noch zustande bekommen könntest: unter der Stativschraube, meist durch Lack überzogen gibt es eine Madenschraube, die den Kegelförmigen Durchgang für das Kabel festhält. Problem ist, die Madenschraube sitzt so fest, dass wir sie nur ausbohren konnten. Aber Probieren kann man ja sie herauszuschrauben. Wenn der Bertzel rausgeht prima! Dann passt in die Öffnung das Innenleben einer XLR Männchenbuchse,  also die in ein Gehäuse eingebaut werden. Da hätte man dann einen perfekten zeitgemäßen Anschluss. Wenn das mit der Buchse einsetzen nicht geht, benutze das vorhandene Kabel.

Sonst wie oben.  noch mal zum aufholen:

Ich vermute das Kabel knistert und spratzelt wenn es niederohmig angeschlossen wird, weil das Mikro für hochohmige Eingänge gebaut wurde. Also der Trafo muss raus!  tja, denn mal vorsichtig an die Sache rangehen.

 Mit der Bitte um eine Nachricht wenns funkst oder neue Fragen stellen an  und schau mal beim RadioTheater vorbei, da siehst du das Mikro in „Hammerschlag gold“.

--------------------------------------------------- Country: Manufacturer / Brand: alternative name
Grundig Portugal || Grundig USA / LextronixYear: 1959–1965 Category: Microphone or Pick-up element

Product Specs

Listed3 years ago
ConditionExcellent (Used)
Excellent items are almost entirely free from blemishes and other visual defects and have been played or used with the utmost care.learn more
Brand
Model
Categories
Year
Made In
  • Germany

Reviews of this Shop

1,490
;

Reverb Gives

Your purchases help youth music programs get the gear they need to make music.

Carbon-Offset Shipping

Your purchases also help protect forests, including trees traditionally used to make instruments.

iOS app store button
Android play store button