(Gibson) Thunderbird Bass Wiring Harness, Treble Bleed, No Load Tone, 50’s or Modern Wiring
--- FREE DELIVERY AUSTRALIA WIDE ---
Hand wired, point to point, replacement or upgrade wiring
harness for a Gibson Thunderbird Bass electric bass guitar with Volume, Volume,
Tone, and Input Jack. This can also be used for Epiphone or other Asian made Thunderbird
bass design guitars. (Please mail us if you are unsure of what you require in
regards to component size etc)
There are a handful of Thunderbird Bass wiring
designs/layouts. The harness pictured uses a top body jack. If you require the longer
jack for side mounting please mail us immediately after purchase (or before)
for your specific need/s and price.
Ready for installation and made to the absolute highest of
standards.
Wired with both “treble bleed” volume and “no load” tone
control.
Only top of the line and professional grade components are
used. You can be confident in both the longevity and most importantly the performance
of these parts.
There are NO wiring shortcuts!
Vital connections that are prone to break or short out, such
as the switch or input jack, are insulation wrapped after soldering. There is
also a deliberate amount of extra length left between wired connections.
Insuring that the harness will fit correctly and that the components and
connections will not break from being overly tight.
All harnesses are made in a modern wiring style. However,
upon your request (please see below “important points to note” for contact
instruction) it can be wired in a 50’s style wiring pattern.
All harnesses are “real world” tested upon completion,
assuring you it will be 100% in both quality and operation.
Components:
-Switchcraft USA
- 1/4" Mono Input Jack
THE industry standard for input jacks with a long
and proven track record. EVERY time you plug in your lead you will know it has
the strength and reliability to hold. Most importantly it will not fail on you
with frustrating crackles and loss of signal.
-Sprague USA
.022 mfd Orange Drop Tone Capacitor
Sprague Capacitors have a well renowned, 50+ years,
reputation for reliability, stability, and consistency in tone with no microphonics.
They are a polypropylene and aluminium foil capacitor with orange flame
retardant epoxy shell.
-CTS USA 500k
Vintage 'Dish Back' Audio Taper Volume Pots
CTS Vintage Style 'Dish' Back Audio Taper pot. With
10% tolerance, low friction rotation, and bakelite base plate. Split Shaft, 24
spline , 1 x Nut, 1 x Lock Washer, 1 x Dress Washer.
Note: The threaded portion on the pot shaft that
runs through the body is 9.5mm. This MAY not be long enough for some Les
Paul/Firebird/ SG/or body mounted style guitars and basses. It will depend on
the body/top thickness. You may need pots with 19mm threaded shafts. If you are
unsure please measure or feel free to message and ask first.
-CTS USA 500k
'No Load' Tone Pot
CTS 'No Load' Pot. Split Shaft, 24 spline , 1 x
Nut, 1 x Lock Washer, 1 x Dress Washer.
A “No-Load” pot works like a standard tone control
when used between setting 1-9. Once set to 10 it is then activated to true bypass.
This essentially “removes” the tone control and capacitor from the circuit.
This will give you a cleaner audio path and the tinniest increase in clean
volume.
Note: The threaded portion on the pot shaft that
runs through the body is 9.5mm. This MAY not be long enough for some Les
Paul/Firebird/ SG/or body mounted style guitars and basses. It will depend on
the body/top thickness. You may need pots with 19mm threaded shafts. If you are
unsure please measure or feel free to message and ask first.
-Vintage Cloth
Wire
Quality thick, 22 Gauge, cotton braided, wax
insulated, vintage style, pull back wire used between components.
-Treble Bleed
Circuit
Sprague USA .001
mfd Orange Drop Tone Capacitor
+
120k Allen
Bradley 1/4 watt Carbon Comp resistor
A “Treble Bleed” circuit is added to the volume pot/s
to improve taper and remove the unbalanced roll off. This keeps your clean
tones clean and the high end frequencies consistent when turning the volume up
and down through 1-10. This is the perfect
upgrade if you use manual volume swell as an effect. Or if you are using your
guitar volume pot to react with and against overdrive, distortion, or fuzz
effect pedals.
An Allen Bradley Carbon Comp resistor is used for
the addition of “warmth” in tone. This is not going to change the world in your
overall sound. It will however add a subtle difference that cold sounding
modern made metal resistors can not achieve
Not quite right? Is your wiring
layout or guitar model slightly different or unique? We can make just about any
custom made harness you desire. Please message us directly and we can discuss
what you need.
IMPORTANT POINTS TO NOTE:
-
Switches - Do not include tips (unless otherwise
described).
-
Pots – Do not include knobs (unless otherwise
described).
-
Listing photos are stock photos for advertising.
The harness you receive will have the
exact top of line parts as per photos/description. The workmanship will be of
the same highest quality with all parts thoroughly tested.
-
The majority of all components are US (imperial)
measurement parts. CTS pots require a 3/8"" hole diameter. For metric
/import guitars and basses you will generally need to widen mounting holes.
Import/metric knobs and switch tips will/may not fit correctly and will
possibly need to be replaced.
-
Depending on the thickness of control plates or
body cavities you may need to add an extra washer or two on the inside of the
pot thread to lower the overall height of the pot knob.
-
The harness will be delivered fully soldered,
including switches and jacks. To run through body cavities, jacks and switches
may/will need to be de-soldered and re-soldered.
-
Metal base plates used in the advertised images
are for advertising photos only and not included in the purchased wiring
harness.
-
All harnesses are wired in a “modern” style. If
you require a 50’s style wiring (or any other alterations) please message
IMMEDIATELY after purchase. Otherwise your harness will be posted within 24hrs
(on average) and it will be too late to make changes.
-
We are ALWAYS available to help if you get
stuck. If you run into any issue when soldering your new harness to your
existing pickups/switches/ground wires please make mail us. Harnesses are
always tested and are 100% correct and without fault. Generally if you
experience a problem when installing it will be due to a
short/earthing/backwards soldering issue. We can talk you through the correct
wiring!
--- FREE DELIVERY AUSTRALIA WIDE ---
PLEASE READ AND UNDERSTAND THE BELOW CONDITIONS.
BY BIDDING/BUYING THIS ITEM YOU HAVE ACCEPTED THE FOLLOWING.
- There is no availability for pickup.
- FREE regular postage/courier is offered on all items – Australia only.
- International delivery is possible under strict conditions. Please
contact us first BEFORE making any purchase to organise actual delivery costs
and details.
- Guitars (of any kind), amplifiers, or cabinets can NOT be sent to a PO
Box or Parcel Locker, only small items (such as effect pedals).
- Payment can be made by Paypal or Bank Deposit/Online Transfer.
- If payment is made by Paypal, the item will ONLY be posted/couriered
to your registered Paypal address and name (NO alternative address).
- Do not hesitate to ask any questions, request further photos. We are
always happy to provide as much info as possible on any items prior to
purchase.