Rupert Neve Designs Shelford 5051 Inductor EQ and Compressor

Brand New
Free Shipping
5 in stock
Estimated ship date: December 7, 2020
This seller is open to offers

Buy With Confidence

Reverb Protection has you covered. We provide a safe community for finding the gear you want.

Shipped From
Miami, FL, United States
Joined Reverb
Preferred Seller
Quick Responder

About This Listing

The Rupert Neve Designs Shelford 5051 Inductor EQ and Compressor combines the classic 3-band EQ from Rupert Neve's vintage circuit designs with the flexibility and power of the Portico II compressor. Using a fully discrete class-A signal path combined with high-performance input and output transformers, the combination EQ and compressor upholds the world renown reputation of the master circuit designer.

The EQ section of the module uses a custom-tapped inductor with selected capacitors to form the mid-range equalizer band and the shelf curves are based on Neve's vintage Modules. Each of the EQ sections uses a low feedback class-A discrete electronics to prevent low-level artifacts from distracting from the tonal shaping of your signal.

The high and low bands can be switched from shelf to peak curves and both offer 15 dB of boost or cut. The high band can be switched from 8,000 to 16,000 Hz and the low band can be set to 35, 60, 100, or 220 Hz. The mid band offers six center frequencies at 200, 350, 700, 1500, 3000, and 6000 Hz. The mid band also features a high peak switch to narrow the bandwidth or increase the Q of the filter. An 18 dB/octave high-pass filter with two corner frequencies that can be toggled between Off, 60, and 120 Hz.

The EQ can be switched to pre or post compressor in the signal chain. It also allows for the two XLR balanced inputs on the back of the unit to be switched from the front panel which allows setups such as having a mic preamplifier and a line input from a DAW to be pre-patched and selected at will.

The compressor section of the module uses a discrete class-A signal path from the Portico Series of signal processors with individual control over threshold, attack, release, make up gain, ratio, side chain HPF, Feed-Forward/Feed-back selection and Peak/RMS detection modes. If you deactivate the compressor the unit can be used as a transformer-coupled high-performance line amplifier.

The compressor has the ability to switch between feed-forward and feed-back operation, and two modules can be linked together for stereo operation. The unit is intended for use with 5088 consoles or with 5285 vertical frames. There are two ±24V power supply options. One 5-way power supply can be placed at the bottom of the rack or a separate 25-way power supply in a 2U enclosure may be used. Using the external module provides clean power with less heat build-up within the modules associated with the DC to DC up-conversion.

Inductor EQ Provides the sonic character of Rupert Neve's classic EQ designs with modern performance HPF Provides 18 dB/octave high-pass filter with two corner frequencies on an illuminated button that toggles between Off, 60 Hz, and 120 Hz Low EQ Enables ±15 dB shelf or peak at 35, 60, 100, and 220 Hz Mid EQ Provides ±15 dB with 6 center frequencies at 200, 350, 700, 1500, 3000, and 6000 Hz with high peak switch to narrow the bandwidth and increase the Q of the filter High Shelf Enables ±15 dB shelf or peak selectable at 8,000 to 16,000 Hz Compression Allows signals below a defined threshold to be amplified linearly or have the gain reduced by a defined ratio when the signal exceeds the threshold Makeup Gain Provides -6 to +20 dB SC HPF Allows the compressor to disregard sustained low frequency content by introducing a HPF at 250 Hz to the VCA side chain signal Ratio Enables compression ratio from 1:1 to 40:1 (hard limiting) Threshold Offers a range from -30 to +20 dBu Attack Time Engages the compressor within 20 to 75 ms Release/Recovery Time Provides a range of release times from 100 ms to 2.5 s Stereo Operation Allows for two 5051 modules to be linked together Ducking Allows the signal from one linked 5051 module to control the amplitude of the second linked module Meters Show Output Levels and gain reduction from -10 to +22 dBu and from +1 to 22 dBu respectively

Product Specs

ConditionBrand New (New)
Brand New items are sold by an authorized dealer or original builder and include all original packaging.learn more

Seller Reviews


Reverb Gives

Your purchases help youth music programs get the gear they need to make music.

Carbon-Offset Shipping

Your purchases also help protect forests, including trees traditionally used to make instruments.

iOS app store button
Android play store button