Ended listing banner

Anyone can sell on Reverb

List your item today to get it in front of thousands of eyes, quickly and easily. Learn more on the Seller Hub.

Similar Listings

Crown - NCDI2x600-U-US - CDi DriveCore 2|600 Amplifier - 1200 W RMS - 2 Channel

Brand New
Free Shipping
Sold Out
If you watch the listing, we'll notify you if it becomes available again.
Shipped From
Chantilly, VA, United States
Joined Reverb
Preferred Seller
Quick Shipper

About This Listing

Brand NEW!  
About Crown Audio CDI 2X600 The CDi DriveCore Series is an evolution in amplification, providing an impressive mix of high-performance; rich feature set, and competitive cost. Using technology derived from our flagship Installed Sound amplifier (Crown DriveCore Install series), the CDi DriveCore 2|600 offers streamlined functionality to work in almost any medium sized installation such as cinema, houses of worship, bars, lounges, and more. Designed for ease-of-use in a variety of applications, the 2|600 is a 2-channel amp that includes network control/monitoring, high-level DSP, front-panel interface, and support for driving up to 100Vrms speaker loads without requiring a transformer. The entire CDi DriveCore line comes pre-loaded with JBL speaker tunings to help make installations quicker and easier.  
DriveCore Technology Crown's proprietary DriveCore technology eliminates hundreds of components within each amplifier, reducing the variability of component values, increasing reliability, resulting in incredible audio fidelity from an efficient design.  
Network Control and Monitoring Through HARMAN's HiQnet Audio Architect software, the CDi DriveCore can be controlled, configured, and monitored through standard TCP/IQnetwork.  
DSP On-board Digital Signal Processor in each amplifier allows for custom configuration and includes these integrated features:  
• Input Router • Input Delay • Up to 1000ms • Input Parametric EQ - 8 band • Crossover • Output Parametric EQ - 8 band • Output Delay - Up to 100ms • LevelMAX Limiter  
Direct Drive 70/100Vrms Output Each output channel is capable of providing either 70V or 100V for high impedance applications.  
Front-Panel Interface Completely configure the amplifier using an intuitive front-panel interface.  
GPIO/AUX Port Recall presets, mute channels, monitor faults, power on/off the amplifier, and more through a combined GPIO/AUX Port.  
Pre-loaded Speaker Tunings For quicker and easier setup and installation.  
Crown Audio CDI 2X600 Features Exclusive multi-patented DriveCore Technology - The patented DriveCore integrated circuit combines hundreds of discrete circuits into one chip for better performance, lower power consumption, and improved reliability Supports configuration and control using HiQnet Audio Architect Monitoring and control over TCP/IP Color LCD and front panel user interface for amplifier configuration, control, and monitoring Programmable GPIO (general purpose input/output) control port Digital signal processing (Input/output EQ filters, crossover, input/output delay, LevelMAXTM limiters) Support for importing of FIR filter coefficients 20 device presets - 1 factory and 19 user 96kHz/32-bit floating-point signal processing Universal power supply with PFC for reduced current draw and industry-leading efficiency Power saving modes Remote power off - Sleep mode activated via AUX port 70Vrms/100Vrms direct drive Each channel independently configurable for low z or high z operation Advanced protection circuits - Amplifier and loads are protected against shorted outputs, DC, mismatched loads, overheating, over/under-voltage, and high-frequency overload Complies with GreenEdge by HARMAN - Environmentally friendly practices in design, manufacturing, and packaging complement energy-efficient operation Included speaker tunings for various JBL speaker models Support for BSS Audio Soundweb Contrio Ethernet wall controllers  
Crown Audio CDI 2X600 Specifications BLU link - No Channels - 2 Network Control - Yes DSP - Yes Control Port - Yes Sensitivity - 0.7V RMS (for full rated power at 8 ohms)Rated Power Output - Dual-Mode 300W @ 2 Ohm 600W @ 4 Ohm 600W @ 8 Ohm 300W @ 16 Ohm  
Bridge Mono Mode 600W @ 4 Ohm 1200W @ 8 Ohm 1200W @ 16 Ohm Load Impedance Dual Mode - 2 - 16 Ohms; 70Vrms and 100Vrms Load Impedance Bridge Mono - 4 - 16 Ohms; 140Vrms and 200Vrms Analog Input Signal to Noise Ratio - > 104dB (ref. rated power, 100V, 20Hz - 20kHz) at 8 ohms) THD - 0.35% (full rated power, 20 Hz - 20 kHz) Damping Factor - > 1000 (20 Hz to 100 Hz) Frequency Response - +/-0.5dB (8 Ohm, 20 Hz - 20 kHz) Crosstalk 20 Hz to 1 kHz - > 80dB (below rated power) Input Impedance - 20 k Ohm balanced, 10 k Ohm unblanced (nominally balanced, nominally unbalanced)Power Supply ConnectorStandard IEC type 320 inlet for detachable connector 100 - 240V (Approx.)Dimensions (W x H x D)19 x 3.5 x 12.25" (48.3 x 8.89 x 31.1cm) (depth not including 1.3" front panel protrusion) Weight - 14.56 lb (6.6kg)  
- All international buyers are responsible for all tax, duties and/or customs fees.

Reviews of this Shop


Product Specs

ConditionBrand New (New)
Brand New items are sold by an authorized dealer or original builder and include all original packaging.learn more
Made In
  • China

Reverb Gives

Your purchases help youth music programs get the gear they need to make music.

Carbon-Offset Shipping

Your purchases also help protect forests, including trees traditionally used to make instruments.

iOS app store button
Android play store button
The Apple logo and the App Store are trademarks of Apple Inc. Google Play and the Google Play logo are trademarks of Google LLC.
Oops, looks like you forgot something. Please check the fields highlighted in red.