CreepTree / SwampTree
Incredibly rare and the most intense device ever created by Reverse Landfill. This is a one of a kind instrument, never to be made again.
Handmade drone / noise synthesizer.
The case is made of a solid block mahogany hardwood. The case is hollowed out with a router tool to fit the electronics.
The "appletree" picture is laser-engraved.
The wood is finished with tung oil & clear laquer.
Potmeters are all 16mm Alpha's, knobs are red plastic.
On the back the case is closed off with a metal plate. It has rubber / soft feet.
Sounds:
Section 1: (Drone)
Dual triangle oscillators are hard-switched through an analog switch by a fast squarewave clock.
Then the signal goes into a lowpass filter.
Sounds vary from deep rumbling drones to phasing screaming lead sounds.
You have control over the two pitches of the main oscillators, the clock frequency and the filter cutoff.
Section 2: (Noise)
4 squarewave oscillators that modulate each others frequency,
go through a clock divider and are mixed together.
You have control over the four pitches of the oscillators.
Section 3: (patchbay)
There are 24 patchpoints.
9 of these are touch based (also patchable by 4mm banana jacks), the other 15 points are 2mm banana sockets.
Drone section patchpoints: OSC1, OSC2, Clock
Noise section patchpoints: 12 clockdivisions, noise1, noise2, mix1, mix2, mix3
Output:
2x 6.3mm jack output.
Power:
Power: 9v/12v bus for adapter (outer ring is GND, center pin is +V)
Note: Power Adapter not included.
Size:
24x19x6 cm
Sounds similar to the video links, but each device has it's own personality.
Incredibly rare and the most intense device ever created by Reverse Landfill. This is a one of a kind instrument, never to be made again.
Handmade drone / noise synthesizer.
The case is made of a solid block mahogany hardwood. The case is hollowed out with a router tool to fit the electronics.
The "appletree" picture is laser-engraved.
The wood is finished with tung oil & clear laquer.
Potmeters are all 16mm Alpha's, knobs are red plastic.
On the back the case is closed off with a metal plate. It has rubber / soft feet.
Sounds:
Section 1: (Drone)
Dual triangle oscillators are hard-switched through an analog switch by a fast squarewave clock.
Then the signal goes into a lowpass filter.
Sounds vary from deep rumbling drones to phasing screaming lead sounds.
You have control over the two pitches of the main oscillators, the clock frequency and the filter cutoff.
Section 2: (Noise)
4 squarewave oscillators that modulate each others frequency,
go through a clock divider and are mixed together.
You have control over the four pitches of the oscillators.
Section 3: (patchbay)
There are 24 patchpoints.
9 of these are touch based (also patchable by 4mm banana jacks), the other 15 points are 2mm banana sockets.
Drone section patchpoints: OSC1, OSC2, Clock
Noise section patchpoints: 12 clockdivisions, noise1, noise2, mix1, mix2, mix3
Output:
2x 6.3mm jack output.
Power:
Power: 9v/12v bus for adapter (outer ring is GND, center pin is +V)
Note: Power Adapter not included.
Size:
24x19x6 cm
Sounds similar to the video links, but each device has it's own personality.
Reverb Buyer Protection
Reverb has your back if your item is lost, damaged, or doesn't match its description. Simply report any issues within 7 days and we'll help you get a full refund.Learn more about Reverb Buyer Protection.
Listed | 4 years ago |
Condition | Mint (Used) Mint items are in essentially new original condition but have been opened or played.Learn more |
Brand | |
Model |
|
Finish |
|
Year |
|