Module A-110-1 is a voltage-controlled oscillator. This VCO's frequency range is about eight octaves (ca. 15Hz ... 8kHz). It can produce four waveforms simultaneously: rectangle, sawtooth, triangle, and sine wave (triangle and sine shapes are not perfect, see remark below). The output levels are typically 8Vpp for saw and rectangle, and 10Vpp for triangle and sine. The frequency or pitch of the VCO is determined by the position of the octave (Range) switch and tuning (Tune) knob, and by the voltage present at the CV inputs. Frequency modulation (FM) of the VCO is therefore a possibility. Footage (the octave of the fundamental) is set by the Range control in five steps, and Fine tuning controlled by the Tune knob. The tune knob range is about +/-1 semitone for older modules. Since about middle of 2015 the value has been increased to about+/- 1/2 octave. In the   is described how to modify the range.
You can control the pulse width of the square wave either by hand, or by voltage control - Pulse Width Modulation or PWM.
For more detailed information please look at the user's manual
. In addition the  is available as an example for the A-100 service manual that is available at extra charges. This document describes also how to modify the sensitivity of the tune control (changing the value of the resistor R5), how to re-adjust the 1V/octave scale and the frequency offset (i.e. the absolute pitch). Such modifications should be carried out by experienced users only !

Technical remarks:

Socket CV1 is normalled to the internal control voltage coming from the bus (interruptible by removing the jumper labelled "INT.CV", located next to the bus connector). Plugging a patch cable into the socket CV1 does interrupt the internal bus CV connection ! Other VCO modules may behave different in this regard (e.g. adding the internal bus CV to the CV applied to the socket at the front panel).

The core of the A-110-1 is a sawtooth oscillator (in contrast to the , which is based on a triangle oscillator). The other waveforms are derived from the sawtooth by internal waveform converters. As the sawtooth reset (i.e. the back-to-zero slope) is not infinite fast but takes a little bit of time the derived waveforms triangle and sine are not perfect ! At the top of the waveform they have a small glitch or notch that is caused by the sawtooth reset and cannot be eliminated by the waveform converters. The sine is derived from the triangle by a simple diode-based converter and the sine shape is not perfect (only a rounded triangle). To obtain a nearly perfect sine signal the triangle-to-sine converter module  is recommended. It includes also a voltage controlled crossfader to fade between two waveforms.

If a perfect triangle is required the  or  is recommended. For a perfect sine wave the thru zero quadrature VCO  or the quadrature LFO/VCO  is recommended.

The sawtooth output of the A-110-1 has a falling (or negative) slope as shown on the front panel.

The rotary switch used for "Range" has 10 positions. But only the positions marked at the front panel (-2 ... +2) should be used. Unfortunately the rotary switch cannot be limited mechanically to 5 positions only.

A simpler VCO (without sine, without rotary switch, but with linear FM input) is the module .
A very small VCO is the module  is the right choice.
A VCO with extended functions is the high end VCO .
More special VCOs are e.g. the Trapezoid Quadrature VCO  or the Quadrature Sine VCO .

Remark: Module A-110 has been renamed to A-110-1 to distinguish it better from other modules of the A-110 series (e.g. , , )


This item is sold As-Described

This item is sold As-Described and cannot be returned unless it arrives in a condition different from how it was described or photographed. Items must be returned in original, as-shipped condition with all original packaging.

Product Specs

Condition:
Mint (Used)
Brand
Doepfer
Model
A-110-1 STANDARD-VCO
Categories
Eurorack

About The Seller

MOOG AUDIO
Joined Feb 2018
MONTREAL, Canada

Quick
Shipper

Accepted Payment Methods

Shipping Policy

Ships from MONTREAL, Canada to:

United States
$19.85
Canada
$10.32

I will ship with tracking to the listed regions. To negotiate shipping rates to other locations, please send me a message.

Tax Policies

This shop collects taxes in the following regions:

Location Tax Rate
Saskatchewan, CA 5.0%
Nunavut, CA 5.0%
Prince Edward Island, CA 15.0%
Yukon Territory, CA 5.0%
Northwest Territories, CA 5.0%
Newfoundland and Labrador, CA 15.0%
New Brunswick, CA 15.0%
Nova Scotia, CA 15.0%
Manitoba, CA 5.0%
British Columbia, CA 5.0%
Alberta, CA 5.0%
Ontario, CA 13.0%
Quebec, CA 14.975%
Tax is calculated automatically in checkout for the following U.S. states:
Alabama*
Arizona*
Connecticut*
District of Columbia*
Iowa*
Minnesota*
New Jersey*
Oklahoma*
Pennsylvania*
South Carolina*
South Dakota*
Washington*
Wyoming*
*State sales tax is required in this region. Learn More

Return Policy

Return Window

This item is sold As-Described and cannot be returned unless it arrives in a condition different from how it was described or photographed. Items must be returned in original, as-shipped condition with all original packaging.

Accepted Payment Methods

Credit Card
Reverb Bucks
Paypal

MOOG AUDIO

MONTREAL, Canada
Joined: Feb 2018

Seller Achievements

Doepfer A-110-1 STANDARD-VCO
$168.39
+ $19.85 Shipping