Module A-110-2 is a low-cost voltage-controlled oscillator. It's a slightly reduced version of the standard VCO A-110-1. Compared to the A-110-1, the A-110-2 has no sine output and the (expensive) octave rotary switch is replaced by a 3-position toggle switch. In return, the A-110-2 is equipped with an additional linear FM input and a soft sync input. A jumper is used to select the range of the tune control between about 1/2 octave and about 4 octaves. The width of the module is only 8 HP compared to the 10 HP of the A-110-1.

All other features are essentially the same as for the A-110-1.

Explanation of the jumpers and trimming potentiometers:

- JP2: CV connection to A-100 bus
- JP3: range of Tune control (installed = about 4 octaves, not installed = about 1/2 octave)
- JP4: AC/DC coupling of the linear FM input (installed = DC coupling, not installed = AC coupling)
- P5: 1V/Oct scale
- P6: frequency offset
- P7: high-end trim
- P8: adjustment +1 Oct. range switch
- P9: adjustment -1 Oct. range switch
- P10: temperature VCO heater

The core of the A-110-2 is - like the A-110-1 - a sawtooth oscillator (in contrast to the A-111-1, which is based on a triangle oscillator). The other waveforms are derived from the sawtooth by waveform converters. As the sawtooth reset (i.e. the back-to-zero slope) is not infinitely fast but takes a little bit of time the triangle is not perfect! At the bottom of the waveform it has a small glitch or notch that is caused by the sawtooth reset and cannot be eliminated by the waveform converter. If a perfect triangle is required, the A-111-1 is recommended.

The sawtooth output of the A-110-21 has a falling (or negative) slope. The front panel shows erroneously a rising (or positive) slope. This has no influence on the sound but becomes important when the module is used as an LFO or is mixed with the sawtooth output of another VCO.

The control voltage applied to the socket 1V/Oct is added to the control voltage coming from the bus (interruptible by removing the jumper JP2). Connecting a cable to the socket 1V/Oct does not interrupt the bus CV connection!

Product Specs

Condition:
Brand New (New)
Brand:
Doepfer
Model:
Doepfer A-110-2-V Eurorack Basic VCO Module (Vintage Black)
Finish:
Black
Categories:
Eurorack

About The Seller

Signal Sounds
Joined Feb 2017
Glasgow, United Kingdom

Accepted Payment Methods

Shipping Policy

Available for local pickup from Glasgow, GLG, GB

Ships from Glasgow, GLG, GB to:

United Kingdom
$0.00
European Union
$10.64
North America
$18.62
Everywhere Else
$21.28

We use a combination of Royal Mail, UPS, DPD and Fedex depending on where you are in the world and the value of your order.

Anything over £50 is normally sent by a Tracked service.

Tax Policies

This seller doesn't charge tax on their sales.

Return Policy

Return Window

This product can be returned within 14 days of receipt.

General Terms

Items must be returned in original, as-shipped condition with all original packaging and no signs of use. Buyer assumes responsibility for all return shipping costs unless the item was not received as described.

Refunds

Buyer receives a full refund in their original payment method less any shipping costs.

Message Seller
  • 2 Watchers

Accepted Payment Methods

Credit Card
Reverb Bucks
Paypal

Signal Sounds

Glasgow, United Kingdom
Joined: Feb 2017

Seller Achievements

Doepfer A-110-2-V Eurorack Basic VCO Module (Vintage Black)
$166.24
+ $18.62 Shipping