lite use HomeBrew Electronics Uno Mos Preamp Boost (+ feet) HBE Uno Mos, ONE control Gain

Here is a used (light average wear) HomeBrew Electronics (HBE) Uno Mos Boost Overdrive MOSFET (also called HomeBrew Electronics Uno Mos Preamp MOSFET Boost).

The bottom side has a big piece of hook type of velcro. The velcro is on tight.  Please let me know if you would like me to take off the velcro.

Comes with a new set of small square black rubber feet (sorry not pictured).  Please let me know if you do not need the feet.

Sorry NO box, NO paperwork, and NO battery.

Unlike some HBE Uno Mos Boost Oveedrive pedals that I have seen (and had) - the one in this listing has the graphic on the top mid center and it does say UNO MOS on the top lower area.

This effect pedal is the single channel version of the Homebrew Electronics Dos Mos.

HBE single-knob boost pedal based on their Dos Mos dual-channel Mosfet booster.  Perfect for pushing an overdriven tube amp to saturation, making your lead lines "pop" out of the mix, and hitting another boost or OD pedal with some extra input steam. The Uno Mos can give you up to 30db of gain.

Made by hand.

Made in the USA

NOTE - the underside of the bottom plate says made in Taiwan (this is because the casing is made in Taiwan - but the  pedal is handbuilt in the USA).

The pedal was tested and works fine.

The color of the finish is orange with a hint of sparkle. That is why you see the tiny white specks in the pictures. But in person you cannot really see the specks in the finish.

The pedal was used - therefore it has a couple of imperfections:  a couple of chips in the finish (most are on the top edges), some nicks, and a few scratches.

TOP SIDE:  There area some tiny & very small nicks and a few short not too light / not too deep  scratches.  Also - there are a couple of chips in the finish (on the edges).

RIGHT SIDE:  There area few tiny & very small nicks, a few short not too light / not too deep scratches, the center area has a longer diagonal scratch.  Also - there are a few chips in the finish (on / near the top edge).

LEFT SIDE: Mostly very clean- it juts has a few very tiny nicks.

FRONT SIDE:  There are some tiny & very small nicks and a few light short scratches. Also - there is small chip in the finish on the top edges (but this chip is really part of the chips that I mentioned in the condition the top side).

BACK SIDE:  There are some tiny light nicks. Also - there is small chip in the finish on the top edges (but this chip is really part of the chips that I mentioned in the condition the top side).

BOTTOM SIDE  ---  The areas near the edges have a few very tiny nicks and a few very short light scratches.  NOTE: There is a big piece hook type of velcro on the bottom - so this pedal is pedal board ready. I will leave the velcro on.  I am not sure of the condition of the bottom plate under the velcro.   Also I am not sure if the label is on the bottom (under the velcro).  If it is - mostly likely it will peel off if you decide to take the velcro off. 

Please let me know if you would like me to take off the velcro for you.

The velcro is on tight. You can soften the adhesive (which will make it easier to pull off the velcro) by using a blow dryer on a warm or hot setting to take off the velcro.   Again - please let me know if you would like me to take off the velcro for you.

As mentioned above -  a new set of small square black rubber feet is included (in case you need them).

the control is: Gain (variable gain control from -10db to +30db)

the jacks are: IN, OUT, and power

I took pictures of all sides of the pedal (and a few of areas of interest). 

NOTE:   There may be some imperfections that I overlooked.   There are some imperfections that can be seen in person that do not appear in the pictures.  Also  - there are some imperfections (glares, reflections, dust specks) that show up in the pictures that are not that visible in person.

• Comes from a smoke free and pet free environment.
  
• Feel free to ask questions.
  
• I will discount shipping on combined purchases.

• USA Shipping with is USPS Priority Mail.  
• International Shipping is with First Class Mail International.
  
  

The following is information on this model pedal:

This pedal is based on their Dos Mos dual-channel Mosfet booster.  This pedal is the single channel version of the Homebrew Electronics Dos Mos.

Perfect for pushing an overdriven tube amp to saturation, making your lead lines "pop" out of the mix, and hitting another boost or OD pedal with some extra input steam.

There are some good demos on YouTube -- check them out!

More info:
HBE pedals were /are made by hand in Arizona, USA. Made by Joel Weaver.
Now defunct, HomeBrew Electronics (HBE) was a small company dedicated to building top quality custom guitar effects pedals. Each pedal was carefully hand crafted one at a time using only the highest quality components and the utmost attention to detail. HBE offered a wide range of effects, blending vintage designs with modern technology, concepts, and features.

Features:
True hardwire bypass switching 
Metal, open frame, chassis mount input/output jacks
Chassis mount 9V DC adapter jack (adapter not included)
Heavy duty chassis mount metal shaft potentiometers and switches
Metal film resistors & capacitors
Heavy gauge teflon-coated wire
Solid mounted PC boards
Heavy duty battery clip/holder
Die-cast metal enclosure