Vintage Kenwood KR-6200 Fm/Am Analogue Stereo Receiver, Back Lit Dial, Phono, Wood Cab, Original Box

Vintage Kenwood KR-6200 Fm/Am Analogue Stereo receiver with back lit analogue tuning dial, back lit signal strength and tuning meters, excellent phono and FM section, very nice original well cared for working condition purchased from the original owner. It has always been in a non smoking climate controlled environment. It comes with the original double box and packing and owners manual. It is in very nice cosmetic condition, a beauty. All controls were cleaned and it is ready to plug and play. It sounds as good as it looks and was made when Kenwood was at the top of their game. It was quality made and designed in Japan. It has bipolar discrete output transistors, beautiful fit, finish, craftsmanship and design. See the specs below. The shipping cost includes safe packing, insurance, prompt shipping and tracking number. Buy with confidence, see my feedback. Good listening, SonnY :)  It is 120/220 volt optional.
Specifications Amplifier Section Dynamic Power Output (IHF): 240 watts both channel at 4 Ω 91 kHz) 190 watts both channel at 8 Ω (1 kHz) Continuous Power Output: 80/80 watts each channel at 4 Ω (1 kHz) 60/60 watts each channel at 8 Ω (1 kHz) 60/60 watts both channel at 4 Ω (1 kHz) 50/50 watts both channel at 8 Ω (1 kHz) 45/45 watts both channel at 8 Ω from 20 - 20,000 Hz Total Harmonic Distortion (at rated): 0,5% Total Harmonic Distortion (at -3 dB rated): 0,1% Intermodulation Distortion (at rated): 0,5% Intermodulation Distortion (at -3 dB rated): 0,2% Frequency response: High Level Input : 20 - 40, 000 Hz ±2 dB Power Bandwidth (IHF): 13 - 30,000 Hz Input Sensitivty/Impedance: Phono: 2,5 mV/ 50 k Ω Mic : 3 mV/ 50 k Ω Aux 1 and 2 : 180 mV/50 k Ω Tape Play A and B : 180 mV/ 50 k Ω Recording Output: Tape Rec A and B : 180 mV DIN : 36 mV Damping Factor (at 8 Ω): 50 Huma nad Noise: Phono : 65 dB Mic : 55 dB Aux 1 and 2 : 75 dB Tape Play 1 and 2 : 75 dB Speaker Impedance: 4 - 16 Ω Tone Control: Bass : ±12 dB at 100 Hz Mid : ±8 dB at 1 kHz Treble : ±12 dB at 10 kHz Filter Low : -7 dB at 100 Hz High : -10 dB at 10 kHz Loudness Control 9-30 dB): +10 dB at 100 Hz; +5 dB at 10 kHz FM Tuner Section Antenna Impedance: 300 Ω, 75 Ω Usable Sensitivity (IHF): 1,7 µV Harmonic Distortion (at 400 Hz, 100% mod.): Mono : 0,5% Stereo : 0,6% Signal-to-Noise Ratio: 66 dB Capture Ratio: 1,5 dB Selectivity (IHF): 65 dB Image rejection: 80 dB IF Rejection: 100 dB Spurious Signal Rejection: 100 dB AM Suppression: 70 dB Stereo Separation: 40 dB at 1 kHz; 25 dB at 10 kHz Sub Carrier Suppression: 60 dB Muting level: 10 µV Quieting Slope: 52 dB at 5 µV; 59 dB at 10 µV; 66 dB at 50 µV Frequency Response: 20 - 15,000 Hz +0,5 dB, -2 dB Front End: 2 FETs (1 DG), 4 Gang IF Stage: 1 IC, 3 element mechanical filters AM Tuner Section Antenna: Built-in ferrite bar antenna and external antenna terminal Usable Sensitivity (IHF): 15 µV Signal-to-Noise Ratio: 45 dB Selectivity (IHF): 35 dB Image Rejection: 70 dB IF rejection: 70 dB Front End: 3 Gang IF Stage: 2 stages General Semiconductors: 2 FETs, 1 ICs, 54 Transistors, 45 Diodes Power Requirement: 110, 120, 220, 240 V 50/60 Hz Power Consumption: 320 at full power Dimensions (W x H x D): 17-1/8" x 5-3/4" x 14" Weight: 29 lbs Included: Walnut cabinet

Specifications

Tuning range: FM, MW

Power output: 45 watts per channel into 8Ω (stereo)

Frequency response: 20Hz to 40kHz

Total harmonic distortion: 0.5%

Damping factor: 50

Input sensitivity: 3mV (mic), 2.5mV (MM), 180mV (line)

Signal to noise ratio: 55dB (mic), 65dB (MM), 75dB (line)

Output: 180mV (line), 36mV (DIN)

Speaker load impedance: 4Ω to 16Ω

Semiconductors: 2 x FET, 1 x IC, 54 x transistors, 45 x diodes

Dimensions: 17-1/8 x 5-3/4 x 14 inches

Weight: 29lbs